Cisco ASR 1001 Hardware Installation Guide

DETAILED STEPS
Step 1
Attach an ESD-preventive wrist strap between you and an unfinished chassis surface.
Step 2
Remove the new Cisco ASR 1000 series route processor from its static shielding bag.
Step 3
Using both hands, grasp the Cisco ASR 1000 Series route processor by its metal carrier edges and orient the it so that
its printed circuit board components are upward.
Handle the Cisco ASR 1000 Series route processor by the carrier edges and handle only; never touch the
printed circuit board components or connector pins.
Caution
Step 4
Align the left and right edges of the Cisco ASR 1000 Series route processor printed circuit board between the route
processor slot guides.
Step 5
Gently slide the Cisco ASR 1000 Series route processor all the way into its chassis slot until you feel the connectors seat
with the router midplane.
Step 6
Seat the route processor in the router midplane by tightening its captive installation screws with a number 2 Phillips or
a 3/16-inch flat-blade screwdriver.
What to Do Next
This completes the procedure for replacing the Cisco ASR 1000 Series route processor in a Cisco ASR 1006
and Cisco ASR 1004 Router.
Removing and Replacing Cisco ASR 1000 Series Route Processor
Internal Hard Drive
Cisco ASR 1000 Series Routers support the Cisco ASR1000-RP1 and the Cisco ASR1000-RP2 route processors.
This section contains the following topics:
Cisco ASR1000-RP1 Spare Hard Drive Accessory Kit
The Cisco ASR 1000 Series RP1 spare hard drive ships with an accessory kit.Verify that the following items
have been shipped in the accessory kit before you remove and replace a damaged Cisco ASR 1000 Series
RP1 module internal hard drive:
•
Hard drive assembly
•
Two cables
•
Tie wrap
•
One EMI wrist strap
Follow these procedures to remove and then replace the Cisco ASR1000- RP1 internal hard drive in the Cisco
ASR 1006 and Cisco ASR 1004 Router.
Cisco ASR 1000 Series Router Hardware Installation Guide
476
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing and Replacing Cisco ASR 1000 Series Route Processor Internal Hard Drive

Cisco ASR 1001 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	-
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
USB ports quantity	1
Ethernet LAN (RJ-45) ports	4
VPN tunnels quantity	8000
Product color	Gray
Rack capacity	1U
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	250 W
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	8192 MB
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %

Weight and Dimensions

Depth	461.5 mm
Width	439.42 mm
Height	43.43 mm
Weight	11350 g