GRAUPNER mc-32 - Page 139

345 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

139

Program description - Dual Rate / Expo | Helicopter models

0%

0%

0%

Roll

Nick

Tail

DUAL

–––

–––

SEL

–––

–––

–––

100%

111%

100%

EXPO

SEL

C3

Normal

Note:

The vertical dashed line shows the current

pitch axis stick position.

Set the Expo values as necessary in the same man-

ner.

Table of Contents

Default Chapter2
- Table of Contents2
General Notices Warning and Note Symbols3
- Safety Notices4
- Safety Notices and Handling Regulations for Lithium-Ion (Liio) and Lithium-Polymer (Lipo) Batteries8
- Environmental Protection Notices10
- Foreword10
- Remote Control Set Description13
- Technical Data16
General Operating Notices Transmitter18
- Opening the Transmitter Housing18
- Transmitter Power Supply18
- Recommended Chargers (Accessory)19
- Battery Operation Timer19
- General Charging Notices20
- Lithium Battery CR 203220
- Stick Length Adjustment20
- Stick Conversions21
- Transmitter Neckstrap Support Bars22
- Installation of Switches, Switch Modules and Knob Modules22
- Aligning the Antenna22
Transmitter Description Front Side23
- Face-Side Connectors24
- Charger Socket24
- DSC Jack24
- Mini USB Connector25
- Data Jack25
- Card Slot26
- Headset Connector27
- Ext.ppm27
- Spi28
- Bottom Side Transmitter Interior29
- Display and Keypad30
- Operating the "Data Terminal31
Commissioning the Transmitter48
- Transmitter Firmware Updates50
- Restoring the Transmitter Software51
Receiver Initialization52
- Receiver Firmware Updates53
- Secure Receiver Settings53
Installation Notices54
- Receiver Power Supply55
- Definitions of Terms58
- Physical Control, Switch and Control Switch Assignments60
- Digital Trim62
Winged Models64
- Receiver Layout65
- Servos in Wrong Direction66
Helicopter Models68
- Receiver Layout69
Program Descriptions70
- Loading a New Memory Location70
- Model Select73
- Copy / Erase74
Suppress Codes80
Suppress Models81
Basic Settings, Model82
- Winged Model82
- Helicopter Model92
Model Type104
Helicopter Type108
Servo Adjustment112
Stick Mode114
- Winged Model114
- Helicopter Model116
Control Adjust118
- Winged Model118
- Helicopter Model122
Dual Rate / Expo132
- Winged Model132
- Helicopter Model136
- Channel 1 Curve Winged Model140
Channel 1141
- Helicopter Model143
Switch Display146
Control Switch146
Logical Switches150
- How Do I Program a Flight Phase152
Phase Settings154
- Winged Model154
- Helicopter Model158
Phase Assignment160
Phase Trim« (Winged Model)162
- Non-Delayed Channels163
- Timers (General)164
- Flight Phase Timers168
  - What Is a Mixer171
- Wing Mixers172
  - Aileron175
  - Aileron and 1 Camber Flap176
  - Ailerons178
  - 2/4 Ailerons and 1/2/4 Camber Flaps180
- Helicopter Mixer190
  - Adjusting the Throttle and Pitch Curve202
  - Autorotation Setting206
  - General Remarks about Freely Progr. Mixers208
- Free Mixers209
  - Linear Mixers213
  - Exponential Mixers215
  - Examples218
- MIX Active/Phase220
- MIX Only Channel221
- Dual Mixer222
- Swashplate Mixer223
- Fail Safe224
- Teacher/Pupil226
  - Connection Schematic229
  - Wireless Hott System230
- Transmitter Output234
- Profi-Trim236
  - Winged Model236
  - Helicopter Model238
- Trim Memory240
  - Winged Model240
  - Helicopter Model242
- Telemetry244
  - Important Notes244
  - Setting & Dataview246
    - Satellite Mode of Two Receivers255
    - Sensor/S257
  - Selecting Sensors258
  - RF Status View259
  - Select Voice Update260
- Channel Sequence262
- Multichannel264
- Ring Limiter268
- MP3-Player272
- Basic Settings275
- Servo Display282
- Servo Test283
- Code Lock284
- Info Display286
  - Introduction288
Programming Examples288
- Winged Model First Steps290
  - Incorporating an Electric Drive296
- Helicopter Model328
Appendix Fcc Declaration342
- Conformity Declaration343
- Guarantee Certificate344

Other manuals for GRAUPNER mc-32

Programming Manual324 pages

Related product manuals

GRAUPNER mc-32 HoTT

Preview: GRAUPNER Kingpad mc-32 Edition

GRAUPNER Kingpad mc-32 Edition

Preview: GRAUPNER MC-32EX

GRAUPNER MC-32EX

Preview: GRAUPNER mc-16

Preview: GRAUPNER MC-28

Preview: GRAUPNER mc-26

Preview: GRAUPNER MC-20 HoTT

GRAUPNER MC-20 HoTT

GRAUPNER HoTT MC-20 Series

Preview: GRAUPNER HoTT MC-16 Series

GRAUPNER HoTT MC-16 Series

Preview: GRAUPNER mz-24 PRO

GRAUPNER mz-24 PRO

Preview: GRAUPNER MX-12 - PROGRAMMATION

GRAUPNER MX-12 - PROGRAMMATION