GRAUPNER mc-32

330
Programming examples - Helicopter models
an unallocated model memory is not possible.
• “Global”, ie specifi c sender, receiver bound to re-
spond to the signals of all model memories “their”
station! A “wrong” model memory if necessary to
recognize only the warning of the missing return
channel.
So If necessary, change the line “Binding type” and
change the setting accordingly:
Stick mode
1
n/a
BASIC SETTINGS, MODEL
Info
n/a
n/a
Module
n/a
HoTT
SEL BD1 BD2 BD3 BD4
Binding type
Global
“Module”
In this line the binding process between model mem-
ory and receiver is initiated, as described in detail on
page 94. Otherwise, you cannot address the receiver.
Afterward, use the  selection key of the left or right
four-way button to move up to the fi rst line and begin
with the actual model programming in the “Model
name” line:
Model name
Stick mode
Module
1
n/a
BASIC SETTINGS, MODEL
n/a
Info
n/a
n/a
Starlet
SEL
HoTT
BD1 BD2 BD3 BD4
2345g/090911
… which must be assembled from characters avai-
lable on the second page of the "Model name" line:
»Base settings, model« (from page 92)
To this end, switch to the line "Module".
Model name
Stick mode
Module
1
n/a
BASIC SETTINGS, MODEL
n/a
Info
n/a
n/a
Starlet
SEL
HoTT
BD1 BD2 BD3 BD4
2345g/090911
Note:
After con rmation of the model selection in
the base screen, if you con rm the message
appearing in the screen for a few seconds …
BIND. N/A
OK
… with a tap on the SET key of the right touch pad,
this line will be accessed automatically.
“Binding type”
If your transmitter is equipped with the latest fi rmware
or has since been updated accordingly, you should
briefl y deal yet with the differences between the two
available HoTT synchronization methods before the
actual binding process. Set default “model”:
Stick mode
1
n/a
BASIC SETTINGS, MODEL
Info
n/a
n/a
Module
n/a
HoTT
SEL BD1 BD2 BD3 BD4
Binding type
Model
• “Model” -specifi c bound receivers respond only
to signals of them explicitly allocated memory
model. One, possibly unintentional, operating on
!"#$%&’()
Model name
Starle
@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_
?+,–./0123456789:;
¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ
`abcdefghijklmnopqrstuvwxyz{|}~
After entering the "Model name", the settings adopt-
ed from »Basic settings« for "Stick mode" and
"DSC Output" are to be checked and changed as
necessary for the given memory location.
The entry fi eld in the "Info" line can be used if needed
for a notice of up to 15 characters in length. This
notice will then be helpful in the selection of models
and so on.
Another option is to be activated in the "Autorota-
tion" line. Even if you are not an advanced pilot, the
autorotation switch should at least be set as an emer-
gency shutoff switch for the motor.
Do this by selecting the "Autorotation" line with a
brief tap on the centre SET key of the right touch
pad, activate the switch assignment, assign a 2-way
switch, e. g. "2", and put it in its "ON" position.
BASIC SETTINGS, MODEL
SET SET
RF transmit on
RF range test 99s
DSC Output PPM10
2I
Autorotation
The selected switch should be in a location on the
transmitter which is easily within reach – without letting
loose of a stick – e. g. above the pitch stick.