HP P2000

HP P2000 G3 MSA System CLI Reference Guide 291
Example
# show advanced-settings
...
<OBJECT basetype="advanced-settings-table" name="advanced-settings-table" oid="1">
<PROPERTY name="background-scrub" type="string">Disabled</PROPERTY>
<PROPERTY name="background-scrub-numeric" type="string">0</PROPERTY>
<PROPERTY name="background-scrub-interval" type="uint16">24</PROPERTY>
<PROPERTY name="partner-firmware-upgrade" type="string">Disabled</PROPERTY>
<PROPERTY name="partner-firmware-upgrade-numeric" type="string">0</PROPERTY>
<PROPERTY name="utility-priority" type="string">Medium</PROPERTY>
<PROPERTY name="utility-priority-numeric" type="string">1</PROPERTY>
<PROPERTY name="smart" type="string">Enabled</PROPERTY>
<PROPERTY name="smart-numeric" type="string">1</PROPERTY>
<PROPERTY name="dynamic-spares" type="string">Enabled</PROPERTY>
<PROPERTY name="emp-poll-rate" type="string">5</PROPERTY>
<PROPERTY name="host-cache-control" type="string">Disabled</PROPERTY>
<PROPERTY name="host-cache-control-numeric" type="string">0</PROPERTY>
<PROPERTY name="sync-cache-mode" type="string">Immediate</PROPERTY>
<PROPERTY name="sync-cache-mode-numeric" type="string">0</PROPERTY>
<PROPERTY name="missing-lun-response" type="string">Not Ready</PROPERTY>
<PROPERTY name="controller-failure" type="string">Enabled</PROPERTY>
<PROPERTY name="controller-failure-numeric" type="string">16</PROPERTY>
<PROPERTY name="super-cap-failure" type="string">Enabled</PROPERTY>
<PROPERTY name="super-cap-failure-numeric" type="string">4</PROPERTY>
<PROPERTY name="compact-flash-failure" type="string">Enabled</PROPERTY>
<PROPERTY name="compact-flash-failure-numeric" type="string">512</PROPERTY>
<PROPERTY name="power-supply-failure" type="string">Enabled</PROPERTY>
<PROPERTY name="power-supply-failure-numeric" type="string">64</PROPERTY>
<PROPERTY name="fan-failure" type="string">Enabled</PROPERTY>
<PROPERTY name="fan-failure-numeric" type="string">128</PROPERTY>
<PROPERTY name="temperature-exceeded" type="string">Enabled</PROPERTY>
<PROPERTY name="temperature-exceeded-numeric" type="string">8</PROPERTY>
<PROPERTY name="partner-notify" type="string">Enabled</PROPERTY>
<PROPERTY name="partner-notify-numeric" type="string">2</PROPERTY>
<PROPERTY name="auto-write-back" type="string">Enabled</PROPERTY>
<PROPERTY name="auto-write-back-numeric" type="string">1</PROPERTY>
<PROPERTY name="disk-dsd-enable" type="string">Disabled</PROPERTY>
<PROPERTY name="disk-dsd-enable-numeric" type="string">0</PROPERTY>
disk-dsd-enable string Shows whether available disks and global spares will spin down after a period
of inactivity shown by the disk-dsd-delay property.
• Disabled: Non-vdisk spin down is disabled. This is the default.
• Enabled: Non-vdisk spin down is enabled.
disk-dsd-
enable-numeric
string Numeric equivalents for disk-dsd-enable values.
• 0: Disabled
• 1: Enabled
disk-dsd-delay uint16 Specifies the period of inactivity in minutes after which available disks and
global spares automatically spin down. If spin down is enabled, the default is 15
minutes. The value 0 means spin down is disabled.
background-
disk-scrub
string Shows whether disks that are not in vdisks are automatically checked for disk
defects to ensure system health.
• Disabled: Background disk scrub is disabled. This is the default.
• Enabled: Background disk scrub is enabled.
background-
disk-scrub-
numeric
string Numeric equivalents for background-disk-scrub values.
• 0: Disabled
• 1: Enabled
Table 9 advanced-settings-table properties (continued)
Name Type Description