Princeton Instruments PI-MAX4 - List of Tables

List of Tables 17
Figure B-9: Outline Drawing: PI-MAX4: 1024i-RF with F-mount Adapter . . . . . .283
Figure B-10: Outline Drawing: PI-MAX4: 1024i-RF with Spectroscopy-mount
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .284
Figure B-11: Outline Drawing: PI-MAX4: 1024i-RF Power Supply. . . . . . . . . . . . .285
Figure B-12: Outline Drawing: CoolCUBE
II
Circulator . . . . . . . . . . . . . . . . . . . . . .286
Figure D-1: Extender Bracket Kit Mounted to a PI-MAX4 . . . . . . . . . . . . . . . . . . .291
Figure E-1: F-Mount (Nikon) Lens Adapter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .294
Figure G-1: Magnetic Screwdriver with Reversible Flat and Phillips Bit . . . . . . . .305
Figure G-2: Standard PI-MAX4 Mount Adapters. . . . . . . . . . . . . . . . . . . . . . . . . . .306
Figure G-3: Standard, IVUV, and NVUV Spectroscopy Mounts. . . . . . . . . . . . . . .307
Figure G-4: Positioning the 2.739” (ID) O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . .308
Figure G-5: Positioning the 2.614” (ID) O-ring . . . . . . . . . . . . . . . . . . . . . . . . . . . .308
List of Tables
Table 2-1: PI-MAX4 System Installation Procedure. . . . . . . . . . . . . . . . . . . . . . . . . .29
Table 4-1: Configuration Parameters by Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Table 6-1: Internal Sync Information for Gated Operation . . . . . . . . . . . . . . . . . . . . .99
Table 6-2: Single Shot Experiment Time Budget . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Table 7-1: Internal Sync Information for Gated Operation . . . . . . . . . . . . . . . . . . . .128
Table 7-2: Single Shot Experiment Time Budget . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Table 12-1: Typical Picosecond Gating Information: PI-MAX4:1024i . . . . . . . . . . .192
Table 13-1: Phase Sweep Information for Sweep > 360° . . . . . . . . . . . . . . . . . . . . . .206
Table 13-2: PI-MAX4: 1024i-RF Connectors, Indicators, and Switches . . . . . . . . . .213
Table 13-3: PI-MAX4: 1024i-RF Power Supply Connectors, Indicators,
and Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .215
Table 14-1: Mask/Window Sizes for 16 x 16 CCD, Full Frame . . . . . . . . . . . . . . . . .225
Table 17-1: Issues with Recommended Troubleshooting Procedures. . . . . . . . . . . . .259
Table A-1: Input Power Specifications: External PI-MAX4 Power Supply . . . . . . .267
Table A-2: PI-MAX4 Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . .268
Table A-3: CCD Array Specifications for Electron Multiplied PI-MAX4
Detectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .268
Table A-4: CCD Array Specifications for non-EM PI-MAX4 Detectors . . . . . . . . .269
Table A-5: AUX I/O Interface TTL Signal Specifications . . . . . . . . . . . . . . . . . . . .270
Table A-6: AUX I/O Connector Pinout and Signal Descriptions. . . . . . . . . . . . . . . .270
Table A-7: AUX I/O Interface Cable Pinout and Signal Information . . . . . . . . . . . .272
Table C-1: WinX-to-LightField Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . .287
Table C-2: LightField-to-WinX Cross Reference . . . . . . . . . . . . . . . . . . . . . . . . . . .289
Table G-1: Adapter Kit Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .305