177
System Settings
System Tempo
5–300
Sets the system tempo.
* When Sync Mode is set to “SLAVE,” the tempo will synchronize to the clock mes-
sages received from an external MIDI device, so the tempo value will be ig-
nored.
* The tempo value is not saved even if you save the System settings.
Tempo Override
OFF, ON
Specify whether the system tempo will change (ON), or will not change (OFF)
when you switch performance.
Device ID
(Device ID Number)
17–32
When you want to transmit or receive System Exclusive messages, set this param-
eter to match the Device ID number of the other MIDI device.
Perform Ctrl Ch
(Performance Control
Channel)
1–16, OFF
Performance Ctrl Ch selects the MIDI receive channel used during switching of per-
formances when MIDI messages (Program Change/Bank Select) are sent from an
external MIDI device. Set this to “OFF” if performances are not to be switched
from an external MIDI device.
If only a program change is received, and if the Perform Ctrl Ch setting
coincides with the MIDI receive channel of a part, priority will be given to
switching the performance.
Patch Rx Ch
(Patch Mode Receive Channel)
1–16
Specifies the channel used to receive MIDI messages in Patch mode.
USB-MIDI Thru
(USB-MIDI Thru Switch)
OFF, ON
Determines the MIDI signal flow from the MIDI IN connector to the SonicCell's
sound generator.
OFF:
Directly transmits the MIDI signals arriving at the MIDI IN connector to the
sound generator, and plays the SonicCell's sound.
ON:
Transmits the MIDI signals arriving at the MIDI IN connector to the
computer via the USB connector. Via its USB connector, the SonicCell
receives the signals that have been THRU’ed by the computer's sequencer
software, and uses them to produce sound with its sound generator.
Powerup Mode
PATCH,
PERFORM
This setting allows you to choose the mode that you want the SonicCell to be in
when it is powered up.
PATCH:
The SonicCell will be in Patch mode when you turn on the power.
PERFORM:
The SonicCell will be in Performance mode when you turn on the
power.
Screen Saver
OFF, 5,
10–60 (min)
Set the time (minutes) until the screen saver begins working.
If this is “OFF,” the screen saver will not appear.
Screen Saver Type
1–6
Select the type of screen saver.
Scale Tune Sw (Switch)
OFF, ON
Turn this on when you wish to use a tuning scale other than equal temperament.
One set of Scale Tune settings can be created in Patch mode. In Performance
mode, this can be set for each part of the performance (p. 72).
The SonicCell allows you to play the keyboard using temperaments other than
equal temperament. The pitch is specified in one-cent units relative to the equal
tempered pitch.
* One-cent is 1/100th of a semitone.
Scale Tune
[SELECT]
Specifies the scale tuning of the patch.
Press [CURSOR/VALUE] to access the Patch Scale Tune screen (p. 178).
Preview
[SELECT]
Makes settings for the Preview function.
Press [CURSOR/VALUE] to access the Preview screen (p. 179).
System Control
[SELECT]
Makes settings for the Control function.
Press [CURSOR/VALUE] to access the System Control screen (p. 179).
System MIDI
[SELECT]
Makes MIDI-related settings.
Press [CURSOR/VALUE] to access the System MIDI screen (p. 180).
Parameter
Value Explanation
MIDI OUT MIDI IN
SonicCell
USB OUT USB IN
USB-MIDI Thru=OFF
MIDI OUT MIDI IN
SonicCell
USB OUT USB IN
USB-MIDI Thru=ON
Sound
Generator
Section
Sound
Generator
Section
SonicCell_e.book 177 ページ ２００７年８月９日 木曜日 午後９時１７分
To Next Page
Loading...
