Roland SonicCell User Manual

248
MIDI Implementation
❍ Cutoff (Controller number 74)
Status
2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode the Part Cutoff Offset parameter (Part Edit)
will change.
❍ Decay Time (Controller number 75)
Status
2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Decay Time value (relative change)
: 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode the Part Decay Offset parameter (Part Edit)
will change.
❍ Vibrato Rate (Controller number 76)
Status 2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change) : 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode the Part Vibrato Rate parameter (Part Edit)
will change.
❍ Vibrato Depth (Controller number 77)
Status 2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change) : 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode the Part Vibrato Depth parameter (Part
Edit) will change.
❍ Vibrato Delay (Controller number 78)
Status 2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change) : 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode the Part Vibrato Delay parameter (Part Edit)
will change.
❍ General Purpose Controller 5 (Controller number 80)
Status 2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (Patch TVA) of Tone 1 will change.
❍ General Purpose Controller 6 (Controller number 81)
Status
2nd byte 3rd byte
BnH 51H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (Patch TVA) of Tone 2 will change.
❍ General Purpose Controller 7 (Controller number 82)
Status
2nd byte 3rd byte
BnH 52H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (Patch TVA) of Tone 3 will change.
❍ General Purpose Controller 8 (Controller number 83)
Status
2nd byte 3rd byte
BnH 53H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (Patch TVA) of Tone 4 will change.
❍ Portamento control (Controller number 84)
Status
2nd byte 3rd byte
BnH 54H kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control
message will change continuously in pitch, starting from the pitch
of the Source Note Number.
* If a voice is already sounding for a note number identical to the
Source Note Number, this voice will continue sounding (i.e.,
legato) and will, when the next Note-on is received, smoothly
change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is
determined by the Portamento Time value.
❍ Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
* In Performance mode the Part Reverb Send Level parameter (Part
Edit) will change.
❍ Effect 3 (Chorus Send Level) (Controller number 93)
Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
* In Performance mode the Part Chorus Send Level parameter (Part
Edit) will change.
SonicCell_e.book 248 ページ ２００７年８月９日 木曜日 午後９時１７分

Roland SonicCell Specifications

General

Brand	Roland
Model	SonicCell
Category	Computer Hardware
Language	English