Xerox WorkCentre 5230 User Manual

February, 2008
6-10
WorkCentre 5225, 5230
IOT NVM List
Launch Version
General Procedures
742-093 Paper Path Sensor (FINISHER) - 0~63 - Bit0: Fin H-X'port Ent. SENSOR Bit1: Fin H-X'port EXIT SENSOR Bit2: Fin X'port
Ent.SENSOR Bit3: Fin Buffer PATH SENSOR Bit4: COMPILE TRAY EXIT PATH SEN
-
SOR Bit5: Not available Bit6: Top Tray Exit Sensor * The meaning of the bit, 0: Out of
paper, 1: Paper detected. The renewal precision is 10 ms.
760-001 TRAY1 for Plain Paper - LEAD REGI ADJUST-
MENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-002 TRAY2-4,HCF for Plain Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-003 MPT for Plain Paper - LEAD REGI ADJUSTMENT 33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-005 DUP ALL SIZE for Plain Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-006 ALL TRAY - REGI LOOP TIMER 33 0~66 0.363mm Loop increases when Set Value is increased.
760-007 TRAY1 for Plain Paper - REGI LOOP TIMER 33 0~66 0.363mm Loop increases when Set Value is increased.
760-008 TRAY2-4,HCF - REGI LOOP TIMER 33 0~66 0.363mm Loop increases when Set Value is increased.
760-009 MPT for Plain Paper - REGI LOOP TIMER 12 0~66 0.363mm Loop increases when Set Value is increased.
760-010 DUP for Plain Paper - REGI LOOP TIMER 33 0~66 0.363mm Loop increases when Set Value is increased.
760-011 REGI CLUTCH OFF TIMER - ALL TRAY 33 0~66 0.363mm Clutch off is delayed by 2ms when Set Value is increased.
760-012 TOP SIGNAL OFFSET VALUE ADJUSTMENT 0 0~99 0.363mm Not available
760-013 DUP A3 Group - LEAD REGI ADJUSTMENT 10 0~16 0.363mm Image input is delayed when Set Value is increased.
760-014 DUP A4S Group - LEAD REGI ADJUSTMENT 10 0~16 0.363mm Image input is delayed when Set Value is increased.
760-015 DUP A4L Group - LEAD REGI ADJUSTMENT 10 0~16 0.363mm Image input is delayed when Set Value is increased.
760-016 TRAY1 for Heavyweight1 Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-017 TRAY1 for Heavyweight2 Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-018 TRAY2-4,HCFfor Heavyweight1 Paper - LEAD
REGI ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-019 TRAY3-4,HCFfor Heavyweight2 Paper - LEAD
REGI ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-020 MPT for Heavyweight1 Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-021 MPT for Heavyweight2 Paper - LEAD REGI
ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-022 DUP ALL SIZE for Heavyweight1 Paper - LEAD
REGI ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-023 DUP ALL SIZE for Heavyweight2 Paper - LEAD
REGI ADJUSTMENT
33 0~66 0.363mm Image input is delayed when Set Value is increased.
760-024 TRAY2-4,HCF for Heavyweight1 Paper - REGI
LOOP TIMER
33 0~66 0.363mm Loop increases when Set Value is increased.
760-025 TRAY3-4,HCF for Heavyweight2 Paper - REGI
LOOP TIMER
33 0~66 0.363mm Loop increases when Set Value is increased.
760-026 MPT for Heavyweight1 Paper - REGI LOOP TIMER 24 0~66 0.435mm Loop increases when Set Value is increased.
Table 5 PH
Chain-
Link Name Default Range 1 Count Remarks

Xerox WorkCentre 5230 Specifications

General

Maximum print size	A3 (297 x 420 mm)
Standard input capacity	500 sheets
Internal memory	No MB
Type	Digital copier