No. Name
User
Setting
C3-04
Slip Compensation Selection during
Regeneration
C3-05 Output Voltage Limit Operation Selection
C4-01 Torque Compensation Gain
C4-02 Torque Compensation Primary Delay Time
C4-03 Torque Compensation at Forward Start
C4-04 Torque Compensation at Reverse Start
C4-05 Torque Compensation Time Constant
C4-06 Torque Compensation Primary Delay Time 2
C5-01
ASR Proportional Gain 1 (for Simple PG V/f
Control)
C5-02
ASR Integral Time 1 (for Simple PG V/f
Control)
C5-03
ASR Proportional Gain 2 (for Simple PG V/f
Control)
C5-04
ASR Integral Time 2 (for Simple PG V/f
Control)
C5-05 ASR Limit (for Simple PG V/f Control)
C6-01 Duty Mode Selection
C6-02 Carrier Frequency Selection
C6-03 Carrier Frequency Upper Limit
C6-04 Carrier Frequency Lower Limit
C6-05 Carrier Frequency Proportional Gain
d1-01 Frequency Reference 1
d1-02 Frequency Reference 2
d1-03 Frequency Reference 3
d1-04 Frequency Reference 4
d1-05 Frequency Reference 5
d1-06 Frequency Reference 6
d1-07 Frequency Reference 7
d1-08 Frequency Reference 8
d1-09 Frequency Reference 9
d1-10 Frequency Reference 10
d1-11 Frequency Reference 11
d1-12 Frequency Reference 12
d1-13 Frequency Reference 13
d1-14 Frequency Reference 14
d1-15 Frequency Reference 15
d1-16 Frequency Reference 16
d1-17 Jog Frequency Reference
d2-01 Frequency Reference Upper Limit
d2-02 Frequency Reference Lower Limit
d2-03 Master Speed Reference Lower Limit
d3-01 Jump Frequency 1
d3-02 Jump Frequency 2
d3-03 Jump Frequency 3
d3-04 Jump Frequency Width
d4-01
Frequency Reference Hold Function
Selection
d4-03 Frequency Reference Bias Step (Up/Down 2)
d4-04
Frequency Reference Accel/Decel (Up/Down
2)
d4-05
Frequency Reference Bias Operation Mode
Selection (Up/Down 2)
d4-06 Frequency Reference Bias (Up/Down 2)
No. Name
User
Setting
d4-07
Analog Frequency Reference Fluctuation
Limit (Up/Down 2)
d4-08
Frequency Reference Bias Upper Limit (Up/
Down 2)
d4-09
Frequency Reference Bias Lower Limit (Up/
Down 2)
d4-10
Up/Down Frequency Reference Limit
Selection
d7-01 Offset Frequency 1
d7-02 Offset Frequency 2
d7-03 Offset Frequency 3
E1-01 Input Voltage Setting
E1-03 V/f Pattern Selection
E1-04 Max Output Frequency
E1-05 Max Voltage
E1-06 Base Frequency
E1-07 Mid Output Frequency
E1-08 Mid Output Frequency Voltage
E1-09 Minimum Output Freq.
E1-10 Minimum Output Freq. Voltage
E1-11 Mid Output Frequency 2
E1-12 Mid Output Frequency Voltage 2
E1-13 Base Voltage
E2-01 Motor Rated Current
E2-02 Motor Rated Slip
E2-03 Motor No-Load Current
E2-04 Number of Motor Poles
E2-05 Motor Line-to-Line Resistance
E2-06 Motor Leakage Inductance
E2-07 Motor Iron-Core Saturation Coefficient 1
E2-08 Motor Iron-Core Saturation Coefficient 2
E2-09 Motor Mechanical Loss
E2-10 Motor Iron Loss for Torque Compensation
E2-11 Motor Rated Output
E2-12 Motor Iron-Core Saturation Coefficient 3
E3-01 Motor 2 Control Method Selection
E3-04 Motor 2 Max Output Frequency
E3-05 Motor 2 Max Voltage
E3-06 Motor 2 Base Frequency
E3-07 Motor 2 Mid Output Frequency
E3-08 Motor 2 Mid Output Frequency Voltage
E3-09 Motor 2 Minimum Output Freq
E3-10 Motor 2 Minimum Output Freq. Voltage
E3-11 Motor 2 Mid Output Freq. 2
E3-12 Motor 2 Mid Output Freq. Voltage 2
E3-13 Motor 2 Base Voltage
E4-01 Motor 2 Rated Current
E4-02 Motor 2 Rated Slip
E4-03 Motor 2 Rated No-Load Current
E4-04 Motor 2 Motor Poles
E4-05 Motor 2 Line-to-Line Resistance
E4-06 Motor 2 Leakage Inductance
E4-07
Motor 2 Motor Iron-Core Saturation
Coefficient 1
E.3 User Setting Table
458
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
To Next Page
Loading...
Need help?
General
