Actelis Networks ML700 - Dry Contact Alarm Indications

To Next Page

To Previous Page

Dry Contact Alarm Indications Troubleshooting

ML700 User Manual 15-5

Dry Contact Alarm Indications

Critical or Major fault (including power input failure) activates (closes) the corresponding

alarm output of the device. The device is normally open and close in case of failure.

Main Page

Default Chapter5
- ML700 Certification5
- General Safety Summary7
- Résumé des Conditions Générales de Sécurité8
- Allgemeine Sicherheitshinweise10
- Table of Contents13
- Contents14
1 Introduction21
- About ML70022
- ML700 Models23
- ML700 Architecture24
- ML700 Topologies25
- Management27
- ML700 Front and Rear Panel Descriptions28
  - ML700 Front Panel Description28
  - ML700 Rear Panel Description29
- ML700 Link with BBA Units31
  - ML700 and BBA Installation31
2 Getting Started33
- Commissioning Procedure34
- Craft Connection to the ML35
- Metaassist View Workplace38
3 Management Configuration48
- NE Management Communication Protocoles and Ports48
- ML Link Visibility Via MAV48
- NE Management Communication Protocols and Ports48
- Opening a Metaassist View Session50
- IP/LAN Connectivity on Directly Connected NE57
- IP/LAN Connectivity on Indirectly Connected NE58
- L2 (MGMT VLAN) Connectivity60
- L3 (IP) Connectivity60
- SNMP Agent and Trap Parameters61
- System Name Configuration66
- Date and Time Setting67
4 Equipment and Port Configuration71
- System-Wide Settings72
  - System Pane72
  - System Configurable Attributes73
- Alarms and Indications Control75
  - General Purpose Output (GPO) Configuration75
  - Environmental Alarm (GPI) Configuration77
- SFP Pluggable Modules78
  - SFP View Provisioning Options78
  - Mitop, Miric and Mirici SFP Management Access80
- Modem Line Ports (MLP)84
  - MLP Workspace84
  - MLP Configuration86
- High Speed Link (HSL)87
- Ethernet Port95
- Static Link Aggregation (LAG)109
5 Ethernet Bridge, STP/RSTP116
- Ethernet Bridge Pane116
- Ethernet Bridge117
- LLDP Configuration121
- MAC Filtering123
- IGMP Snooping127
- STP/RSTP and Provider Bridge Configuration134
6 Modem Profiles Management Model144
- Xdsl Background144
- Profile Configuration Workspace145
- Rate Profiles146
- Spectral Profiles149
- Quality Management165
- Configuring Templates173
7 Quality of Service (Qos)176
- Overview176
- Classification Method177
- Rate Limit179
- L2 (Cos) / L3 (Dscp/Tos) Queuing Priorities180
- Classification182
- Cos Marking183
- Scheduler and Queue Congestion Control185
  - Scheduler Configuration186
  - Auto WFQ188
8 VLAN Configuration189
- VLAN Configuration Principles190
- Management VLAN Configuration191
- Traffic VLAN Configuration193
- VLAN Control Overview195
- VLAN Membership Principles and Rules196
  - VLAN Membership Principles196
  - Membership Rules200
9 L2CP Processing201
- Supported L2CP Protocols202
- Configuring Handling of L2CP Frames203
- Deployment Considerations206
10 Ethernet Service Configuration211
- Introducing MEF Terminology212
- MEF10 Qos Flow Overview214
- EVC Connection Definition215
- VLAN and EVC Mapping216
- BW Profile Definition217
- EVC Services Definition220
- Identification Rules Definition223
- Deployment Considerations234
11 Ethernet Operation, Administration and Management235
- 802.1Ag CFM236
  - 802.1Ag OAM Configuration Overview236
  - CFM MEP Monitoring and Analysis Tools244
- Y.1731 Ethernet OAM253
12 Security Management264
- Configuring Session Access Warning Text264
- Managing User Accounts265
- Password Control270
  - System Wide User Settings270
  - Editing Password in Session272
- Locking out Users273
  - Lock a User Account273
  - System Wide Lockout Behavior273
- Managing Sessions275
  - User Session Information275
  - Viewing and Managing Current Logged in Sessions275
- Radius277
- IP Access Control List (ACL)283
- SSH - Secure Shell287
13 Monitoring298
- Control of Alarmed Conditions298
- Error Counters, Measurements and Threshold Alerts308
- Ethernet Performance Monitoring321
- HSL Link Monitoring337
- Copper Line Monitoring344
14 Administration353
- Using Metaassist View354
- Using Web Browser373
- CLI Usage Guidelines381
15 Troubleshooting387
- Recommended Test Equipment388
- LED Fault Indications389
- Dry Contact Alarm Indications391
- Alarmed Conditions392
  - Troubleshooting Workflow392
  - Field Descriptions393
- Copper Line Troubleshooting395
- Ethernet Service Troubleshooting402
  - Non-Alarmed Service Problems402
  - Ethernet Service Fault Isolation Tools406
- Management Connection Problems411
- Resolving Management Connection Problems415
Appendix A - Technical Specifications421
- ML700 Specifications422
- ML700 Supported SNMP Mibs425
- Customer Logs426
Appendix B - Parts List427
- SFP Modules427
- Cables430
- Accessories432
Appendix C - Step-By-Step Commissioning Procedures433
- CO Site Installation434
- CO Configuration - for Link Verification435
- CPE Physical Site Installation436
- ML CO - Service Configuration437
- ML CO - Administration Configuration438
- ML CO - Configuration Backup439
Appendix D - Ethernet Service Configuration Step-By-Step441
- Service Configuration Procedure442
- Service Configuration Details443
Appendix E - Factory Setup Content446
- Factory Setup446
- Rules and Services449
Appendix F - Alarms Troubleshooting451
- System Alarms Troubleshooting452
- Equipment Alarms Troubleshooting453
- Modem Ports Alarms Troubleshooting455
- HSL Alarms Troubleshooting458
- Ethernet Port Alarms Troubleshooting460
- MEP Alarm Troubleshooting461
Appendix G - VLAN Topologies465
- Symmetric Topologies466
- Asymmetric Topologies470
Appendix H - Environmental Alarm Condition Types477
Appendix I - Recommended Actelis Mitop Configuration Parameters479
- Mitop System Parameters480
- Mitop Physical Layer Parameters483
- Mitop Applications Parameters484

Actelis Networks ML700 - Dry Contact Alarm Indications

Table of Contents