Anritsu MT8852B - 16-3 Saving Results

To Next Page

To Previous Page

IQ Data Output (Option 17) Saving Results

MT8852B Operation Manual PN: 13000-00205 Rev. N 16-3

16-3 Saving Results

The results of measurement can be saved to a text file or printed in the style shown below.

Figure 16-2. EDR Test Results

Main Page

Default Chapter3
- Safety Symbols3
- License6
- Table of Contents14
Chapter 1-General Information20
- About this Manual20
- Product Description22
- Combitest24
- Bluesuite Pro325
Chapter 2 Bluetooth Overview26
- Bluetooth Special Interests Group26
- Bluetooth Qualification26
- Master and Slave Devices26
- Test Mode27
- RF Test Specification Overview27
Introduction to 2-Bluetooth26
- Bluetooth RF Tests28
Chapter 3-Preparation For Use30
- Operating Environment30
- Power Requirements30
- Unpacking the Product31
  - Package Contents31
- Power on Procedure32
- Preparing for Storage32
- Preparing for Shipment32
Chapter 4-Instrument Overview34
- Front Panel Layout34
- Rear Panel Layout41
- Configurations for Testing42
Chapter 5-Test Scripts46
- What Is a Script46
- Selecting a Script47
- Configuring a Script48
- Naming a Script58
- Locking a Script59
- Unlocking a Script60
- Changing the Password60
Chapter 6-Preparing The EUT for Testing62
- Basic Rate and EDR Testing62
- Low Energy Testing68
Chapter 7-Running A Script in Standard Mode70
- Chapter 7 - Running a Script in Standard Mode70
- Supported Tests70
- Testing in Standard Mode71
- Limits72
- Basic Rate Tests73
- Enhanced Data Rate Tests96
- Low Energy Tests110
Chapter 8-Running A Script in Single Payload Mode124
- Single Payload Mode124
- Supported Tests124
- Testing in Single Payload Mode125
- Test Conditions126
- Results126
Chapter 9-Running A Script in Null Packet Mode128
- Null Payload Mode128
- Supported Tests128
- Testing in Null Packet Mode128
Chapter 10-Running A Single Test140
- Running a Single Test140
Chapter 11-Configuration Reference142
- Navigation Table143
- Configuring the MT8852B146
- Configuring the Equipment under Test (EUT)155
- Configuring Scripts159
  - All Scripts Setup159
- Configuring System Features160
- Service Configuration164
Chapter 12-Signal Generator166
- 12-1 Setting up the Bluetooth Interferer166
Chapter 13-CW Measurements168
- 13-1 Performing Continuous Wave Measurement168
Chapter 14-Audio Measurements170
- 14-1 Testing Using Remote Loopback170
- 14-2 Testing the EUT Transmit Path174
- 14-3 Testing the EUT Receive Path175
- 14-4 Putting the EUT into Remote Loopback176
- 14-5 Using Audio Measurements with AFH176
Chapter 15-Adaptive Frequency Hopping (Option 15)178
- Overview of Adaptive Frequency Hopping (AFH)178
- 15-2 AFH Processing179
- AFH in Bluetooth 1.2180
- 15-4 Mt8852B Afh181
- 15-5 AFH Test Configuration182
- 15-6 Assessing AFH182
Chapter 16-IQ Data Output (Option 17)186
- 16-1 Software Overview186
- 16-2 EDR Measurements187
- 16-3 Saving Results188
- 16-4 Handling Results189
  - Generating a Power Burst Profile Graph189
  - Generating Graphs from IQ Data189
Chapter 17-Technical Support190
- 17-1 Contacting Support190
- 17-2 Reporting Problems190
- 17-3 Anritsu Service Centers190
Appendix A-Specifications192
- A-1 MT8852B Specification192
- MT8852B Specification193
Appendix B-Test Conditions206
- Test Condition206
- Glossary207
- B-2 Glossary207
Appendix C-Preset Values212
- Preset Values212
Appendix D-Messages214
- D-1 Error Messages214
- Error Messages215
- Error Codes221
  - Bluetooth Specification 4.0 Devices221
  - Internal HCI and Communication List of Error Codes223
Appendix E-Bit and Frame Error Rates224
Appendix F-Terminology Glossary226
- Terminology Glossary226
Appendix G-Connector Care and Handling228
- Pin Depth Mating Connectors228
- Torquing Connectors229
- Mechanical Shock229
- Cleaning Connectors230
Appendix H-Low Energy Packet Structure232

Anritsu MT8852B - 16-3 Saving Results

Table of Contents

Other manuals for Anritsu MT8852B

Related product manuals