Cisco ASR 1002-X Hardware Installation Guide

Cisco ASR 1002-X
Router
Cisco ASR 1001
Router
Cisco ASR 1002
Router and Cisco
ASR 1002-F
Router
Cisco ASR 1004
Router
Cisco ASR 1006
Router
Cisco ASR 1013
Router
Hardware
Component
Not applicableNot applicableNot compatibleSupportedSupportedNot supportedASR1000-ESP20
Not applicableNot applicableNot compatibleSupportedSupportedSupportedASR1000-ESP40
Not applicableNot applicableNot compatibleNot compatibleSupportedSupportedASR1000-ESP100
Not compatibleNot compatibleNot compatibleNot compatibleNot compatibleSupportedASR1000-ESP200
Not applicableNot applicableNot applicableSupportedSupportedNot compatibleASR1000-RP1
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-RP2
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-SIP10
Not applicableNot applicableNot applicableSupportedSupportedSupportedASR1000-SIP40
ASR 1002 PEM
supported
Supported with
its own AC and
DC power
supplies
ASR 1002 PEM
supported
ASR1004 PEM
supported
ASR 1013 PEM
supported
ASR 1006 PEM
supported
ASR 1013 PEM
supported
ASR1000 PEMs
The following is the outcome of upgrades performed using incompatible combinations of hardware components:
•
The embedded services processor card is disabled and an error message is generated in either of the
following scenarios:
◦
Cisco ASR1000-ESP20, Cisco ASR1000-ESP40, or Cisco ASR1000-ESP100 is inserted in the
Cisco ASR 1002 Router.
◦
Cisco ASR1000-ESP5 is inserted into Cisco ASR 1004 Router, Cisco ASR 1006 Router, or Cisco
ASR 1013 Router.
•
The Complex Programmable Logic Device (CPLD) field programmable upgrade for Cisco
ASR1000-SIP10 cannot be performed in slot 5. Cisco ASR1000-SIP10 can be upgraded only in any one
of the slots from slots 0 to 4.
•
If Cisco ASR1000-RP1 is inserted into Cisco ASR 1013 Router, the card is disabled and an error message
is generated
The Cisco ASR 1013 Router supports only the following components:
•
Cisco ASR1000-RP2
•
Cisco ASR1000-ESP40 or Cisco ASR1000-ESP200
•
Cisco ASR1000-SIP10 or Cisco ASR1000-SIP40
Cisco ASR 1000 Series Router Hardware Installation Guide
6
Cisco ASR 1000 Series Routers Hardware Overview
Hardware Compatibility

Cisco ASR 1002-X Specifications

General

Form Factor	Rack-mountable
Rack Units	2RU
Integrated Services	Yes
Maximum Memory	16 GB
Built-in Gigabit Ethernet Ports	6
Input Voltage	100-240 VAC
Operating Temperature	32 to 104°F (0 to 40°C)
Redundancy	Power supply redundancy
Network Interface Modules	Up to 4 SPA/SIP slots
Embedded Services Processor (ESP)	ESP-20
Maximum Packet per Second (PPS)	15 Mpps
Height	3.5 inches
Fixed Ports	6 GE ports
Memory	4 GB (default), 16 GB (maximum)
Power Supply	Dual power supplies (AC or DC)
Dimensions (H x W x D)	3.5 x 17.5 x 19.0 in (8.9 x 44.5 x 48.3 cm)