Fujitsu PRIMERGY RX1330 M1 Upgrade And Maintenance Manual

Upgrade and Maintenance Manual RX1330 M1
Contents
6.3.3.2 Removing the defective hot-plug power supply unit . . . . . 104
6.3.3.3 Installing the new hot-plug power supply unit . . . . . . . . 105
6.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 105
6.3.4 Replacing the power distribution board . . . . . . . . . . . . . 105
6.3.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 105
6.3.4.2 Removing the defective power distribution board . . . . . . 106
6.3.4.3 Installing the new power distribution board . . . . . . . . . 107
6.3.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 108
6.4 Converting a standard power supply to a redundant power
supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 109
6.4.2 Removing the standard power supply unit . . . . . . . . . . . 109
6.4.3 Installing the upgrade kit . . . . . . . . . . . . . . . . . . . . 110
6.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 114
7 Hard disk drives / solid state drives . . . . . . . . . . . . . 115
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 116
7.2 2.5-inch HDD/SSD configurations . . . . . . . . . . . . . . 117
7.2.1 Equipping the 2.5-inch HDD/SSD bays . . . . . . . . . . . . . 117
7.2.2 Configuration with up to four HDD/SSD modules . . . . . . . . 117
7.2.3 Configuration with up to eight HDD/SSD modules . . . . . . . 118
7.2.4 Configuration with up to 10 HDD/SSD modules . . . . . . . . 119
7.2.5 Installing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . 120
7.2.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 120
7.2.5.2 Removing a 2.5-inch HDD/SSD dummy module . . . . . . 120
7.2.5.3 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . 121
7.2.5.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 122
7.2.6 Removing 2.5-inch HDD/SSD modules . . . . . . . . . . . . . 122
7.2.6.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 122
7.2.6.2 Removing a 2.5-inch HDD/SSD module . . . . . . . . . . 123
7.2.6.3 Installing a 2.5-inch HDD/SSD dummy module . . . . . . . 124
7.2.6.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 124
7.2.7 Replacing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 124
7.2.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 125
7.2.7.2 Removing the defective 2.5-inch HDD/SSD module . . . . 125
7.2.7.3 Installing the new 2.5-inch HDD/SSD module . . . . . . . . 125
7.2.7.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 125

Fujitsu PRIMERGY RX1330 M1 Specifications

General

Number of Processors	1
Memory Slots	4
Maximum Memory	32 GB
Form Factor	1U Rack
Processor	Intel Core i3 product family Intel Pentium product family
CPU Family	Intel Xeon
Memory Type	DDR3 UDIMM
Storage	Up to 4 x 3.5" or 2.5" drives
Drive Bays	4
RAID	0, 1, 5, 10
RAID Controller	Optional
Network	2 x Gigabit Ethernet
Operating System Support	Windows Server, Red Hat Linux, SUSE Linux