Huawei iMaster NetEco V600R021C10 - Page 9

6.4.5.2 Setting Monitoring Parameters for a UPS2000-H (over SNMP).................................................................200
6.4.5.3 Setting UPS5000 Monitoring Parameters (over SNMP)................................................................................ 204
6.4.5.4 Setting UPS5000 Monitoring Parameters (Modbus TCP)..............................................................................208
6.4.5.5 Creating a UPS on the NetEco................................................................................................................................ 210
6.4.6 Adding a PDU................................................................................................................................................................... 213
6.4.6.1 Setting PDU8000 Monitoring Parameters (SNMP)..........................................................................................213
6.4.6.2 Setting PDU8000 Monitoring Parameters (Modbus TCP)............................................................................. 214
6.4.6.3 Creating a PDU on the NetEco............................................................................................................................... 215
6.4.7 Adding an MTS9604B-N20B1/MTS9606B-N20C2 Power Supply................................................................... 217
6.4.7.1 Creating a MTS9604B-N20B1/MTS9606B-N20C2 Power Supply on the NetEco.................................. 217
6.4.8 Adding a SmartLi............................................................................................................................................................ 219
6.4.8.1 Setting SmartLi Monitoring Parameters (Modbus TCP)................................................................................ 219
6.4.8.2 Creating a SmartLi on the NetEco......................................................................................................................... 219
6.4.9 Adding a CO Power Module........................................................................................................................................221
6.4.9.1 Setting Monitoring Parameters for the TP483000D and TP482000B........................................................221
6.4.9.2 Creating a Power Module on the NetEco........................................................................................................... 221
6.4.10 Adding an rPDU............................................................................................................................................................ 223
6.4.10.1 Setting RPDU_HUAWEI_PDU2000-32-1PH-20-4-M2 Monitoring Parameters.................................... 223
6.4.10.2 Creating an rPDU on the NetEco.........................................................................................................................224
6.5 Scenarios for Connecting the ECC800-Pro Outside the Smart Module........................................................... 226
6.5.1 Setting and Adding the ECC800-Pro Collector......................................................................................................226
6.5.1.1 Preparations and Login..............................................................................................................................................226
6.5.1.2 Setting the ECC800-Pro IP Address....................................................................................................................... 229
6.5.1.3 Setting the ECC800-Pro System Type................................................................................................................... 230
6.5.1.4 Setting RS485 Parameters for the ECC800-Pro Collector.............................................................................. 231
6.5.1.5 Setting NetEco Parameters...................................................................................................................................... 233
6.5.1.6 Creating an ECC800-Pro Collector on the NetEco............................................................................................234
6.5.1.7 Setting the Transparent Transmission Function for the ECC800-Pro Collector...................................... 237
6.5.1.8 Setting Transparent Transmission for the UIM20A Expansion Module on the ECC800-Pro WebUI
......................................................................................................................................................................................................... 239
6.5.2 Adding Sensors................................................................................................................................................................ 241
6.5.2.1 Adding Dry Contact Interface Devices..................................................................................................................241
6.5.2.1.1 Setting Door Status Sensor Monitoring Parameters on the ECC800-Pro Web................................... 241
6.5.2.1.2 Setting Smoke Sensor and Water Leakage Sensor Parameters on the ECC800-Pro Web.............. 242
6.5.2.1.3 Setting Device Monitoring Parameters of an NO/NC Dry Contact on the ECC800-Pro Web........243
6.5.2.1.4 Creating an Icon for a Door Status Sensor on the NetEco........................................................................ 244
6.5.2.1.5 Creating the Water Sensor on the NetEco...................................................................................................... 248
6.5.2.1.6 Modifying Alarm Names for Devices on the NetEco...................................................................................251
6.5.2.1.7 Modifying Performance Counter Names for Devices on the NetEco.....................................................252
6.5.2.2 Adding a Temperature and Humidity Sensor.................................................................................................... 252
6.5.2.2.1 Setting Monitoring Parameters for a T/H Sensor (BOM Number: 33010346)...................................253
6.5.2.2.2 Creating a Temperature and Humidity Sensor on the NetEco.................................................................253
6.5.2.3 Adding a Water Leakage Sensor............................................................................................................................ 254
iMaster NetEco
Device Installation and Commissioning Guide (Data
Center) Contents
Issue 02 (2021-05-12) Copyright © Huawei Technologies Co., Ltd. viii