<SwitchD> system-view
[SwitchD] vlan 10
[SwitchD-Vlan10] quit
[SwitchD] interface gigabitethernet 1/0/0
[SwitchD-GigabitEthernet1/0/0] port hybrid pvid vlan 10
[SwitchD-GigabitEthernet1/0/0] port hybrid untagged vlan 10
[SwitchD-GigabitEthernet1/0/0] quit
[SwitchD] interface vlanif 10
[SwitchD-Vlanif10] ip address 3.0.1.32 24
[SwitchD-Vlanif10] quit
# Configure the IP address of the VLANIF interface on Switch F.
<SwitchF> system-view
[SwitchF] vlan 10
[SwitchF-Vlan10] quit
[SwitchF] interface gigabitethernet 2/0/0
[SwitchF-GigabitEthernet2/0/0] port hybrid pvid vlan 10
[SwitchF-GigabitEthernet2/0/0] port hybrid untagged vlan 10
[SwitchF-GigabitEthernet2/0/0] quit
[SwitchF] interface vlanif 10
[SwitchF-Vlanif10] ip address 3.0.1.2 24
[SwitchF-Vlanif10] quit
[SwitchF] vlan 20
[SwitchF-Vlan20] quit
[SwitchF] interface gigabitethernet 1/0/0
[SwitchF-GigabitEthernet1/0/0] port hybrid pvid vlan 20
[SwitchF-GigabitEthernet1/0/0] port hybrid untagged vlan 20
[SwitchF-GigabitEthernet1/0/0] quit
[SwitchF] interface vlanif 20
[SwitchF-vlanif20] ip address 1.0.1.2 24
[SwitchF-vlanif20] quit
# Configure the IP address of the VLANIF interface on Switch A.
<SwitchA> system-view
[SwitchA] vlan 20
[SwitchA-Vlan20] quit
[SwitchA] interface gigabitethernet 1/0/0
[SwitchA-GigabitEthernet1/0/0] port hybrid pvid vlan 20
[SwitchA-GigabitEthernet1/0/0] port hybrid untagged vlan 20
[SwitchA-GigabitEthernet1/0/0] quit
[SwitchA] interface vlanif 20
[SwitchA-vlanif20] ip address 1.0.1.11 24
[SwitchA-vlanif20] quit
Step 3 Configure the NTP multicast server.
# Configure the clock of Switch C as the NTP master clock with the stratum being 2.
<SwitchC> system-view
[SwitchC] ntp-service refclock-master 2
# Configure Switch C as the NTP multicast client and configure Switch C to sense NTP multicast
packets through VLANIF10.
[SwitchC] interface vlanif 10
[SwitchC-vlanif10] ntp-service multicast-server
[SwitchC-vlanif10] quit
Step 4 Configure Switch D, which resides on the same network segment with the server.
# Configure Switch D as the NTP multicast client and configure Switch D to sense NTP multicast
packets through VLANIF10.
<SwitchD> system-view
[SwitchD] interface vlanif 10
[SwitchD-vlanif10] ntp-service multicast-client
[SwitchD-vlanif10] quit
Quidway S9300 Terabit Routing Switch
Configuration Guide - Network Management 3 NTP Configuration
Issue 03 (2010-09-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3-35
To Next Page
Loading...
