Krone Big Pack 890 XC - Tensioning;Relieving the Upper Needle Shaft

Operation
266
Pos: 107.32.1 /Ü berschriften/Ü berschriften 2/A- E/BBallensc hurre heben / s enken @ 280\ mod_14054988 34845_78.doc x @ 2154218 @ 2 @ 1
18.4 Lifting / Lowering Bale Chute
Pos: 107.32.2 / BA/Sicherheit/ 2. Vorangestellte Warnhinweise/W arnung - V erletzungsgefahr , wenn bei la ufendem Traktor motor Funktionen direkt an der M aschine ausg e @ 274\m od_140430487756 8_78.docx @ 2064063 @ @ 1
WARNING!
There is an increased risk of injury if functions are performed directly at the machine
while the tractor engine is running.
If functions are performed directly at the machine while the tractor engine is running, people
standing in the danger zone can be crushed or killed.
• Only operate the machine while the tractor engine is running if
– The PTO shaft is switched off and coasting machine parts have come to a standstill.
– The tractor is secured to prevent it rolling away.
– The parking brake and the flywheel brake on the machine are applied.
– The person operating the machine knows which functions are executed by the various
operations.
– The person operating the machine is standing outside the radius of action of the
moving parts of the machine.
– No other persons are standing in the danger zone.
Pos: 107.32.3 / BA/Bedienung /Gr oßpackenpress e/Hydraulisc h klappbare Rolle nschurre/Be dienung Rollensch urre heben / sen ken Einfü hrtext @ 280\ mod_14055002 98873_78.doc x @ 2154305 @ @ 1
The operation of the bale chute (1) depends on the version you have (medium version
electronics or comfort version electronics).
Pos: 107.32.4 /Ü berschriften/Ü berschriften 3/A- E/A/Ausführu ng Medium-Ele ktronik @ 304\ mod_14145931 45717_78.doc x @ 2362909 @ 3 @ 1
18.4.1 Medium Electronics Design
Pos: 107.32.5 / BA/Bedienung /Gr oßpackenpress e/Hydraulisc h klappbare Rolle nschurreBedi enung Rollensch urre heben / se nken Mediu m-Elektroni k BiG PACK 890/1 270/1290 HS @ 356\mod_14 38682887824 _78.docx @ 26527 47 @ @ 1
Fig.
166
Position a = raise the bale chute
Position b = lower the bale chute
• Close the stop cock (3).
• Actuate the control unit ( ).
• Release the mechanical lock (1) on the bale chute.
• Open the stop cock (2).
Lowering into the working position
• Pull the safety sleeve (4) forwards.
• Move the control lever (5) down into position (b).
Raising into the transport position
• Pull the safety sleeve (4) forwards.
• Move the control lever (5) up into position (a).
• Close the mechanical lock (1) on the bale chute.
Pos: 107.32.6 / BA/Einstellunge n/Großpackenpr esse/Hinweis A bsperrhahn sc hliessen @ 302 \mod_141396 2959913_78. docx @ 23534 45 @ @ 1
Note
The stop cock (2) must be closed during baling mode.
Pos: 107.32.7 /Ü berschriften/Ü berschriften 3/A- E/A/Ausführu ng Komfort-El ektronik @ 304\ mod_1414593 335179_78.docx @ 2362940 @ 3 @ 1