Maintenance - Gearbox
358
Pos: 140.12 /Übers chriften/Übersc hriften 2/P-T /RRaffergetrie be @ 24\mod_ 12415844287 37_78.docx @ 245996 @ 2 @ 1
22.2 Packer gearbox
Pos: 140.13 /BA /Wartung/Öl kontrolle_Wechsel/ Großpac kenpresse/Rafferge triebe Anbring ungsort @ 24\ mod_1241585 198221_78.docx @ 246121 @ @ 1
The packer gearbox (3) is located on the left side of the machine.
Pos: 140.14 /BA /Wartung/Öl kontrolle_Wechsel/ Großpackenpress e/Raffergetri ebe Bild mit Leg ende 1290 HD P II @ 158\m od_136448453 7954_78.docx @ 1391829 @ @ 1
Fig.
Inspection screw / control hole
Pos: 140.15 /BA /Wartung/Öl kontrolle_Wechsel/ Ölkontrolle / Öl wechsel Int ervall: siehe Ka pitel Wartung „W artungstabelle“ @ 134\mod_1 350483605921_ 78.docx @ 1 188115 @ @ 1
Interval for oil level check and oil change: refer to chapter Maintenance “Maintenance Table”
Pos: 140.16 /BA /Wartung/Öl kontrolle_WechselÖlqu alität/Öl menge: siehe Kapitel Technisch e Daten der M aschine @ 37 1\mod_14419 58324612_78.d ocx @ 2710777 @ @ 1
Oil quality/amount of oil: refer to chapter entitled Technical Data of Machine “Operating
Materials”
Pos: 140.17 /BA /Wartung/Öl kontrolle_Wechsel/ Altölentsorg ung: siehe Kapit el Sicherheit „Betri ebsstoffe“ @ 280\mod_14 05428392269 _78.docx @ 21527 65 @ @ 1
Used oil disposal: see chapter Safety "Consumables"
Pos: 140.18 /BA /Sicherheit/8. Vor aussetzungen/H andlungsanweis ung für alle Mas chinen/Ha ndlungsanweis ung: Maschi ne stillsetzen und sichern @ 27 4\mod_14043 65253849_78.d ocx @ 2065151 @ @ 1
• Shut down and safeguard the machine, see chapter Safety -> Safety routines, "Shutting
down and safeguarding the machine".
Pos: 140.19 /BA /Wartung/Öl kontrolle_Wechsel/ Ölkontrolle N EU über Kontr ollschraube ohn e Einfüllschra ube @ 158\mod_ 13644836335 89_78.docx @ 1391741 @ @ 1
Oil level check:
• Screw out inspection screw.
• Oil level up to control hole.
If the oil reaches the control hole:
• Screw in the inspection screw and tighten it securely.
If the oil does not reach the control hole:
• Top up oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 140.20 /BA /Wartung/Öl kontrolle_Wechsel/ Ölwechsel NEU o hne Einf üllschraube @ 15 8\mod_13644 83760090_78.d ocx @ 1391770 @ @ 1
Oil change:
Collect escaping oil in a suitable container.
• Screw out oil drain plug and drain the oil.
• Screw out inspection screw.
• Screw in oil drain plug and tighten it securely.
• Top up new oil via control hole until the control hole is reached.
• Screw in the inspection screw and tighten it securely.
Pos: 140.21 /Layo ut Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0.d ocx @ 4165 @ @ 1
To Next Page
Loading...
