419
Lateral setting of the plunger ............................ 314
LED strips ......................................................... 274
Lifting ................................................................ 345
Lifting Bale Chute ............................................. 267
Lighting ............................................................. 136
Locking self-steering axle ................................. 172
Locking Steering Axle ....................................... 172
Locking the tying process ................................. 301
Logical Alarms .................................................. 240
Lower the bale chute ........................................ 174
Lower the blade bar .......................................... 175
Lowering Bale Chute ........................................ 267
Lubricants ......................................................... 373
Lubricating the cardan shaft ............................. 374
Lubricating the rollers for the blade lever ......... 375
M
Machine overview ............................................... 52
Main drive ..................................................... 60, 62
Main gearbox .................................................... 358
Maintenance ..................................................... 338
Maintenance - Brake System ........................... 364
Maintenance – Central Lubrication ................... 380
Maintenance – electrical system ...................... 381
Maintenance - hydraulic system ....................... 351
Maintenance - lubrication.................................. 372
Maintenance Compressor................................. 370
Maintenance table ............................................ 339
Malfunctions - Causes and Remedies .............. 388
Malfunctions on the knotter .............................. 393
Maximum permissible speed ........... 80, 85, 90, 95
Means of representation ..................................... 14
Notes with information and recommendations 16
Warning signs ................................................. 16
Means of Representation
Figures ............................................................ 13
Menu 1 .............................................................. 190
Menu 1-1 ........................................................... 191
Menu 1-2 ........................................................... 192
Menu 13 Counters ............................................ 205
Menu 1-3 Knotter monitoring ............................ 193
Menu 13-1 Customer counter ........................... 206
Menu 13-1 Detail counter/customer counter .... 208
Menu 13-2 Total counter................................... 211
Menu 1-4 Blow interval ..................................... 194
Menu 14 ISOBUS settings ................................ 213
Menu 14-2 Diagnostics for driving speed /
direction indicator .......................................... 214
Menu 14-8 Configuring main window ............... 215
Menu 1-5 Blowing time ..................................... 195
Menu 15 Settings ............................................. 219
Menu 15-5 Software info .................................. 235
Menu 15-6 Technician level ............................. 236
Menu 2 Sensitivity of direction indicator .......... 196
Menu 3 Central lubrication ............................... 197
Menu 4 Bale scales .......................................... 199
Menu 5 Moisture measurement ....................... 201
Menu 5-1 Alarm message for moisture
measurement ............................................... 202
Menu 5-2 Correction value for moisture
measurement ............................................... 203
Menu 6 Silage additive system ........................ 204
Menu Structure ................................................ 184
Menus
Actuator Test ................................................ 231
Auxiliary (AUX) ............................................. 213
Sensor test ................................................... 220
Switching Between the Terminals ................ 218
Metric Thread Screws with Control Thread ..... 341
Metric Thread Screws with Countersunk Head
and Hexagonal Socket ................................. 342
Metric Thread Screws with Fine Thread .......... 342
Minimum tractor requirements ......... 83, 88, 93, 98
Moisture measurement .................... 201, 202, 203
Moving ............................................................. 147
Moving Baling Ram into Position ..................... 318
Moving Packer Strip into Position .................... 317
Moving the machine without hydraulic connections
..................................................................... 146
MultiBale ............................................................ 58
MultiBale Design ................................................ 58
N
Needle Yoke ...................................................... 65
O
Oil change compressor .................................... 371
Oil level check compressor .............................. 371
Oil quantities and designations for the compressor
..................................................................... 101
Oil quantities and designations for the on-board
hydraulic system .......................................... 101
On-board hydraulic system .............................. 352
On-Board Hydraulic System for Comfort Version
Electronics ................................................... 414
On-Board Hydraulic System for Medium Version
Electronics ................................................... 413
Opening/closing the bale channel flaps ........... 173
Operating Bale Ejector ..................................... 269
Operating Machine via Joystick ....................... 180
Operating the Machine via LS (Load-Sensing
Connection) .......................................... 115, 145
To Next Page
Loading...
