Krone Big Pack 890 XC - Main Gearbox; Maintenance - Gearbox

Settings
319
Pos: 109.98.4 /Ü berschriften/Ü berschriften 3/U- Z/Voreinstell ung Geweind estange / Anschlag @ 107\mod_ 13342254378 31_78.docx @ 964998 @ 3 @ 1
19.19.1 Presetting threaded rod / stop for the feeler rocker
Pos: 109.98.5 / BA/Einstellunge n/Großpackenpr esse/Variables F üllsystem VFS /HS-Baurei heVoreinstellu ng Gewindestang e Anschlag Bild HS-Baureihe @ 352\mod _143748840202 0_78.docx @ 26 36918 @ @ 1
IV
III
II
I
1
2
17
VVI
Fig.
224
Pos: 109.98.6 / BA/Einstellunge n/Großpackenpr esse/Variables F üllsystem VFS/HS -Baurei he/Voreinstellung G ewindesta nge Anschlag Acht ung @ 369\ mod_1441784 070895_78.docx @ 2703415 @ @ 1
ATTENTION! Damage to the machine
To avoid damaging the machine, never move the threaded rod (2) into position (VI).
Pos: 109.98.7 / BA/Einstellunge n/Großpackenpr esse/Variables F üllsystem VFS/HS -Baurei he/Voreinstellung G ewindesta nge Anschlag Acht ung bei Ausfü hrung Multi-B ale @ 272\mo d_140326013 9102_78.docx @ 2050144 @ @ 1
ATTENTION! Damage to the machine
To avoid damaging the machine, never change the position of the feeler rocker (1) on the
MultiBale version.
Pos: 109.98.8 / BA/Einstellunge n/Großpackenpr esse/Variables F üllsystem VFS /Montage Tas tschwinge allge mein @ 24\ mod_12414317 01743_78.doc x @ 244292 @ @ 1
The feeler rocker (1) and threaded rod (2) must be installed in different positions according to
machine type (presetting).
Pos: 109.98.9 / BA/Einstellunge n/Großpacke npresse/Variabl es Füllsystem VFS /Tabelle P osition Tastsch winge / Gewindesta nge_890/127 0/1290 @ 369 \mod_1441784 287062_78.doc x @ 2703442 @ @ 1
Machine type
Position of feeler rocker
Position of threaded rod
BP 1270
I
V
BP 890 / 1290 /
1290 HDP
II
V
Pos: 109.98.10 /B A/Einstellung en/Großpackenpre sse/Variables Füllsystem VFS/H S-Baureih e/Voreinstellu ng Gewindest ange Anschlag Te xt @ 272\ mod_1403259872 815_78.doc x @ 2050058 @ @ 1
The VFS system must be adjusted if
• the bale channel chamber does not fill up sufficiently (the filling of the bale upwards must be
improved)
• the overload clutch of the packer responds too frequently
Procedure:
• Move VFS system to zero position and check settings (see chapter Settings "Zero position")
• Check and, if required, adjust triggering sensitivity (see chapter Settings "Adjusting
triggering sensitivity")
Pos: 109.98.11 /L ayout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_ 0.docx @ 4165 @ @ 1