Krone Big Pack 890 XC - Pressure Limiting Valve Block (On-Board Hydraulic System)

Machine Description
65
Pos: 55.59 /Übersc hriften/Überschrif ten 3/K-O/NN adelschwi nge @ 158\mod _13651400550 04_78.docx @ 1405035 @ 3 @ 1
5.8.5 Needle Yoke
Pos: 55.60 /BA/Be dienung /Groß packenpresse /Überlastsicherung en / Kupplu ngen / Sternratsc he / Scherschr aube/Überlastsic herung der Na delschwinge / Scherschrau be Bild alle H S-Typen außer 1290 HDP II @ 192\mod_13 82077992442 _78.docx @ 16375 26 @ @ 1
Fig.
30
Pos: 55.61 /BA/Be dienung /Groß packenpresse/Üb erlastsicherunge n / Kuppl ungen / Sternr atsche / Scherschr aube/Überl astsicherung der Na delsch winge / Scherschrau be alle HS-T ypen außer 12 90 HDP II @ 1 91\mod_138173 7358783_78. docx @ 1629117 @ @ 1
Shear screw
The connecting rod (1) of the needle yoke is secured by a shear screw, left-hand side of the
machine.
The shear screw protects the needles and the needle yokes against load peaks.
Pos: 55.62 /Übersc hriften/Überschrif ten 2/P-T/P Pick up @ 1\mod_12017 91975201_0.doc x @ 54586 @ 2 @ 1
5.9 Pick-up
Pos: 55.63 /BA/Ma schinenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essen/Pick- up Funktionsbesc hreibung Bild 1 290 HDP II ohn e XC @ 157\ mod_13643151 27180_78.doc x @ 1385997 @ @ 1
Fig.
31
1)
Pick-up
2)
Guide wheel
3)
Spring
4)
Depth limiter
Pos: 55.64 /BA/Ma schinenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essen/Pick- up Funktionsbesc hreibung T1 bei Ausführung o hne Schneid werk @ 168\mo d_13679910649 15_78.docx @ 1 452404 @ @ 1
The pick-up is used to pick up the crop.
The pick-up starts to rotate by turning on the PTO shaft.
Pos: 55.65 /BA/Ma schinenbeschr eibung/Maschi nenübersicht/F unktionsweise/Gr oßpackenpr essenPick-up F unktionsbesc hreibung T2 @ 3 55\mod_14 38667690021_7 8.docx @ 26510 25 @ @ 1
The pick-up (1) is raised and lowered via the single-acting control unit ( ) on the tractor.
The pick-up is equipped with guide wheels (2). The guide wheels are used to adjust the working
height of the pick-up.
The working height of the pick-up can be manually limited downwards by moving the depth
limiter (4) on both sides of the machine. This makes it possible to drive the machine without
guide wheels with the pick-up in fixed position.
The bearing pressure of the guide wheels can be adjusted to the ground conditions via the
spring (3).
Pos: 55.66 /La yout Module /---------------Seitenumbruch---------------- @ 0\mod_11961 75311226_0.doc x @ 4165 @ @ 1