Krone Big Pack 890 XC - Automatic Centralised Lubrication System (Optional); Maintenance - Central Lubrication

Maintenance
342
Pos: 114.16 /Übers chriften/Übersc hriften 2/K- O/MMesserwec hsel @ 8\mo d_121965728 5958_78.docx @ 1 19937 @ 2 @ 1
20.4 Blade Changing
Pos: 114.17 /BA /Wartung/Schneid werk/Messer wechsel allge mein von der lin ken Seite Big Pac k @ 275\ mod_1404469078 762_78.doc x @ 2069681 @ @ 1
Blades are changed in the same way on the right and left side of the machine. The procedure
used on the left side of the machine is described below. The same applies for the right side of
the machine.
Pos: 114.18 /Layo ut Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918 145_0.docx @ 1 092566 @ @ 1
Pos: 114.19 /BA /Sicherheit/6. Ü berarbeitete War nhinweise/ Warnung - Funktio n Messerbal ken heben/senke n betätigen @ 377\mod_144 3161811445_7 8.docx @ 27 36379 @ @ 1
WARNING!
Serious injuries caused by moving machine parts
The blade bar moves by actuating the function “Raise/lower blade bar”. Thus persons could be
seriously injured.
• Make sure that there is no one in the danger zone of the blade bar.
Pos: 114.20 /BA /Wartung/Schneid werk/Achtung - Schneidwer k hochfahren @ 275\mod_1 40446939683 2_78.docx @ 206 9710 @ @ 1
ATTENTION!
You many damage the cutting system if you raise it without first retracting and locking
the knife drawers.
• Ensure that both knife drawers are properly pushed in and locked before the cutting
system is raised.
Pos: 114.21.1 / BA/Wartung/Sc hneidwerk/Mess erwechsel Bild @ 275\mo d_1404401306487 _78.docx @ 2 068091 @ @ 1
5
BPHS0300
3
6
Fig.
239
Pos: 114.21.2 / BA/Wartung/Sc hneidwerk/Schneid werk absen ken zÜ @ 275 \mod_140446 8973233_78. docx @ 2069532 @ @ 1
Lowering the cutting system
Pos: 114.21.3 / BA/Wartung/Sc hneidwerk/Schneid werk absen ken: Medium–Ele ktronik @ 356\mod_143869 8331389_78.d ocx @ 2654 895 @ @ 1
Medium electronics
• Actuate the control unit ( ) on the tractor until the cutting unit has been fully lowered.
Pos: 114.21.4 / Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918 145_0.docx @ 1092566 @ @ 1
Pos: 114.21.5 / BA/Maschinenbesc hreibung/M aschinenübersicht /Großpackenpre ssen/Ko mfort-Elektroni k @ 61\mod_1299 223046976_7 8.docx @ 5709 19 @ @ 1
Comfort - Electronic
Pos: 114.21.6 / BA/Info-Center /CCI-ISOBUS-T erminal/CCI-Bi G Pack/Funktio nstasten F1 bis F 12Messer balken freischalten @ 352\mod _1437392672 909_78.doc x @ 2634130 @ @ 1
Release
• To release the blade bar, press .
The symbols , are shown on the display.
Pos: 114.21.7 / BA/Info-Center /CCI-ISOBUS-T erminal/CCI-Bi G Pack/Funktio nstasten F1 bis F 12Messer balken senken @ 3 52\mod_14 37393051647_78. docx @ 263 4192 @ @ 1
Lowering
• To lower the blade bar, press and hold .
Pos: 114.21.8 / Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918 145_0.docx @ 1092566 @ @ 1
Pos: 114.21.9 / BA/Wartung/Sc hneidwerk/Schneid werk absen ken: Komfort- Elektronik Über die Tasten @ 2 75\mod_1404 467742434_7 8.docx @ 2069479 @ @ 1
Using the pushbuttons on the machine
• To lower the blade bar, press the pushbutton until the blade bar is fully lowered.
Pos: 114.21.10 /L ayout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_134259291 8145_0.doc x @ 1092566 @ @ 1
Pos: 114.21.11 /B A/Wartung/Sch neidwerk/Einz elmessersicher ung entlasten @ 275\mod_1 40446755977 2_78.docx @ 20 69451 @ @ 1
Releasing the single blade locking device
• Shut down and safeguard the machine, see chapter Safety -> Safety routines "Shutting
down and safeguarding the machine".
• Attach the special tool (4) to the upper or knife selection (1, 2).
CAUTION! Risk of injury due to spring pressure on the special tool. If you release it too soon,
you can injure yourself.