Newtec MDM6000 - Allow Changes During Transmission

To Next Page

To Previous Page

Newtec Proprietary

Confidentiality: Unrestricted

V1.0

163/314

Feature Descriptions MDM6000 Satellite Modem

14.1.14.2 Allow Changes during Transmission

• Allow Changes while Tx is on

– enable;

– disable (default value).

The following picture displays the default value.

Disabled Enabled

Main Page

Default Chapter2
- Table of Contents2
1 Copyright11
2 EU Compliancy Statements12
- Radio and Telecommunications Terminal Equipment (R&TTE) Directive 1995/5/EC12
- EMC Information13
- Restriction of Hazardous Substances Directive (Rohs) (Directive 2011/65/EU)13
- Registration, Evaluation and Authorization of Chemicals (REACH)14
- WEEE - Waste Electrical and Electronic Equipment Directive15
3 Safety Regulations16
- Environmental18
- Rack Mounting Instructions18
- Earth Ground19
4 Options20
5 Feedback22
6 About this Manual23
- Version History and Applicability23
- Cautions and Symbols23
- Related Documentation24
7 Introduction25
- Efficiency at the Core25
- Optimal Availability25
- Flexibility and Scalability Matching Market Business Models26
8 Physical Description27
- Front Panel Description27
- Back Panel Description31
9 Block Diagram38
- Device Management39
- Data Input and Output Interfaces39
- BBF over IP in40
- Encapsulation41
- Modulator43
  - PRBS Generator43
  - L-Band TX or IF-Band TX Interfaces43
- Demodulator44
  - L-Band RX a / L-Band RX B Input Interfaces44
- BBF over IP out46
- Decapsulation47
10 Getting Started48
- Set the Management IP Address48
- Set Date and Time49
- Configure and Save50
11 How to Manage the Device51
- Management Model / Menu Tree51
- Management Ethernet Interfaces53
- Management IP Connectivity54
- Ethernet Link Redundancy55
- How to Use the Graphical User Interface57
- How to Use the Front Panel76
- Command Line Interface (CLI)83
- Snmp98
  - Consult the SNMP Mibs99
- File Transfer Protocol (FTP)100
12 General Device Settings and Actions102
- Access Control102
- License File103
  - License Upgrade104
- Configuration Settings105
- Software Upgrade115
  - Software Upgrade Procedure115
- Device Identification117
- Logging117
- Diagnostics Report120
- Date and Time121
- Device Monitoring123
- Device Redundancy123
- Reset the Device125
- Alarm Handling126
- Control Plane131
- Remote Terminals136
  - Configure the Terminals137
  - Monitoring138
- Reference Clock139
- Antenna Control Interface140
13 Data Interfaces146
- Data Ethernet Interfaces146
- Data IP Connectivity147
- Data Ethernet Link Redundancy151
- BBF over IP in154
- BBF over IP out158
- L-Band Rx a / L-Band Rx B160
14 Feature Descriptions161
- Modulator161
- DVB Carrier Identification179
- Equalink181
- PRBS Generator183
  - How to Monitor the Outgoing PRBS Bit Rate184
- Reference Clock185
- Demodulator186
- Flexacm206
- Automatic Uplink Power Control212
- Device Redundancy227
- DC BUC Power on L-Band Tx229
- Stream Encapsulation232
- Stream Decapsulation260
- Test Traffic Generator and Monitoring268
  - Test Traffic Generator268
  - Test Traffic Monitoring270
- Transparent BBF over IP272
- In-Band Remote Management274
  - How to Configure the In-Band Management Feature275
    - Hub Site275
    - Remote Site276
  - Example276
    - Configure the Hub Site277
    - Configure the Remote Site280
15 Appendix - Alarm List281
- Generic Alarms282
- Ethernet Interface Alarms283
- BBF over IP Alarms284
- Modulator Alarms285
- Reference Clock Alarms286
- Demodulator Alarms287
- Alarms: BUC Power Alarms288
16 Appendix - Overview of the Used Technologies289
- DVB-S2, DVB-S2X and S2 Extensions289
- Noise and Distortion Estimator (Node)293
  - How Does Node Work293
- Wideband295
- Clean Channel Technology295
17 Appendix - Classification Expressions296
- Example Expressions299
18 Appendix - Generic Stream Encapsulation300
- GSE Header301
19 Appendix - Technical Specifications302
- Input Interfaces302
- Modulation and Demodulation302
- Modulation Interfaces309
- Demodulation Interfaces311
- Internal 10 Mhz Reference Frequency312
- Generic312
- Physical312
20 Appendix - Back Panel Combinations313
- Module 1313
  - Demodulator Input and Modulator Output Interface313
  - Mains Power Supply Units315
- Module 2317
- Example318
21 Appendix - Acronyms319

Newtec MDM6000 - Allow Changes During Transmission

Table of Contents

Other manuals for Newtec MDM6000

Related product manuals