Parker Compax3 I10T10 - Page 229

Parker EME
Index
192-120100 N16 C3I10T10 - December 2010
229
Mounting and dimensions Compax3S150V2
and S150V4 • 69
Mounting and dimensions Compax3S300V4 •
70
Mounting and dimensions PSUP/C3M • 71
Mounting and dimensions
PSUP10/C3M050D6, C3M100D6,
C3M150D6 • 71
Mounting and dimensions
PSUP20/PSUP30/C3M300D6 • 72
Mounting distances, air currents
Compax3H050V4 • 74
Mounting distances, air currents
Compax3H090V4 • 74
Mounting distances, air currents
Compax3H1xxV4 • 75
N
Nominal value window • 108
Note on error switch-off • 82
Notes on the STO function • 81
O
Offset alignment • 142
Operating Principle • 140
Operator control module BDM • 202
Optimization • 116
Optimization window • 117
Optimize motor reference point and switching
frequency of the motor current • 99
Order code • 165
Order code device
Compax3 • 165
Order code for accessories • 166
Order code for mains module
PSUP • 166
Oscilloscope operating mode switch: • 120
P
Packaging, transport, storage • 12
Parker servo motors • 170
PC - PSUP (Mains module) • 60
PC <-> C3M device combination (USB) • 148
PC <-> Compax3 (RS232) • 145
PC <-> Compax3 (RS485) • 147
Permissible braking pulse power
BRM04/01 with C3S150V2 • 194
BRM04/01 with C3S300V4 • 194
BRM04/02 with C3S150V2 • 195
BRM04/02 with C3S300V4 • 195
BRM04/03 with C3S300V4 • 196
BRM05/01 with C3S063V2 • 192
BRM05/01 with C3S075V4 • 193
BRM05/02 with C3S075V4 • 193
BRM08/01 with C3S015V4 / C3S038V4 • 190
BRM08/01 with C3S025V2 • 190
BRM09/01 with C3S100V2 • 191
BRM10/01 with C3S150V4 • 191
BRM10/02 with C3S150V4 • 192
BRM11/01 with C3H0xxV4 • 196
BRM12/01 with C3H1xxV4 • 197
BRM13/01 with PSUP10D6 • 197
BRM14/01 with PSUP10D6 • 197
Permissible braking pulse powers of the
braking resistors • 188
Plug and pin assignment C3H • 53
Plug assignment Compax3S0xx V2 • 31, 32,
33, 34, 59, 62, 63, 64
Position controller • 135
Power supply • 33
Power supply connector X1 for 3AC
400VAC/480VAC-C3S devices • 36
Power supply plug X1 for 1 AC
230VAC/240VAC devices • 33
Power supply plug X1 for 3AC
230VAC/240VAC devices • 33
Power supply voltage DC C3H • 57
Principle • 126
Process of the automatic determination of the
load characteristic value (load identification)
• 127
PSUP/Compax3M Connections • 40
R
Recommendations for preparing the modem
operation • 162
Ref X11 • 207
Remote diagnosis via Modem • 159
Resolver • 62
Resolver / feedback (plug X13) • 62
Resolver cable • 182
Rising of current (Para) • 138
Rotary servo motors • 172
RS232 cable • 205
RS232 plug assignment • 59
RS232/RS485 interface (plug X10) • 59
RS485 cable to Pop • 206
RS485 plug assignment • 59
RS485 settings values • 154
S
Safe torque off • 76
Safe torque off basic function • 85
Safe torque off description • 85
Safety function - STO (=safe torque off) • 76
Safety instructions • 14
Safety notes for the STO function in the
Compax3M • 88
Safety switching circuits • 87
Safety technology option for Compax3M (axis
controller) • 49
Safety-conscious working • 14
Scope • 118
Scope of delivery • 10
Selection of the supply voltage used • 98
Setpoint control • 107
Setting the axis function • 61
Setting the time basis XDIV • 120
Setting up Compax3 • 96
Settings for channels 1..4 • 121
Setup mode • 141
Signal interfaces • 62
SinCos© cable • 183
Special functions • 122