Parker Compax3 I10T10 User Manual

Parker EME
Index
192-120100 N16 C3I10T10 - December 2010
227
±
±10V analog current setpoint • 134
±10V analog current setpoint commanding and
encoder emulation • 106
±10V analog speed setpoint • 133
±10V analogue speed setpoint commanding
and encoder emulation • 103
A
Access to the hazardous area • 86
Additional conditions of utilization • 19
Adjusting the basic address • 61
Advanced control parameters • 131
Advantages of using the • 77
Alignment of the analog inputs • 142
Analog command interface +/-10V with
encoder simulation • 112
Analog Inputs/Outputs • 63, 163
Analogue / encoder (plug X11) • 63
ASCII - record • 155
B
Ballast resistor • 34, 102, 220
Ballast resistor BRM13/01 & BRM14/01 • 200
Ballast resistor BRM4/0x and BRM10/02 • 199
Binary record • 156
Boundary conditions • 126
Brake delay times • 143
Braking resistor / high voltage DC C3S
connector X2 • 34
Braking resistor / high voltage supply
connector X2 for 3AC
400VAC/480VAC_C3S devices • 37
Braking resistor / high voltage supply plug X2
for 1AC 230VAC/240VAC devices • 34
Braking resistor / high voltage supply plug X2
for 3AC 230VAC/240VAC devices • 35
Braking resistor / supply voltage C3H • 57
Braking resistor / temperature switch PSUP
(mains module) • 46
Braking resistor BRM11/01 & BRM12/01 • 199
Braking resistor BRM5/02, BRM9/01 &
BRM10/01 • 198
BRM10/02 • 187, 192, 199
BRM5/01 braking resistor • 198
BRM8/01braking resistors • 198
C
C3 settings for RS485 four wire operation •
153
C3 settings for RS485 two wire operation • 152
Calculation of the BRM cooling time • 189
Calling up the input simulation • 139
Capacitors • 13
Circuit layout overview • 83
Circuit: • 84
COM port protocol • 154
Command interface • 103
Command value release X12/7= • 66
Communication • 144
Communication Compax3M • 60
Communication in the axis combination
(connector X30, X31) • 60
Communication interfaces • 59
Compax3 communication variants • 144
Compax3 Accessories • 170
Compax3 device description • 26
Compax3 with analogue and step/direction
input • 24
Compax3H connections front plate • 53
Compax3H plugs/connections • 50
Compax3M STO application description • 90
Compax3S connectors • 28
Compax3Sxxx V2 • 33
Compax3Sxxx V4 • 36
Condenser module C4 • 201
Conditions of utilization • 17
Conditions of utilization for cables / motor filter
• 18
Conditions of utilization for CE-conform
operation • 17
Conditions of utilization for the STO function
with Compax3M • 88
Conditions of utilization for UL certification
Compax3H • 22
Conditions of utilization for UL certification
Compax3M • 21
Conditions of utilization for UL certification
Compax3S • 20
Conditions of utilization mains filter • 17
Conditions of utilization STO (=safe torque off)
Safety function • 81
Configuration • 96
Configuration name / comments • 110
Configuration of local modem 1 • 161
Configuration of remote modem 2 • 161
Connect braking resistor C3H • 57
Connection of a braking resistor • 35, 37
Connection of terminal box MH145 & MH205 •
185
Connection of the digital Outputs/Inputs • 64
Connection of the power voltage • 51
Connection of the power voltage of 2 C3H 3AC
devices • 58
Connection of the power voltage of 2 C3S 3AC
devices • 37
Connections of Compax3H • 50
Connections of Compax3S • 28
Connections of the axis combination • 42
Connections of the encoder interface • 63
Connections on the device bottom • 41
Connections to the motor • 181
11. Index

Parker Compax3 I10T10 Specifications

General

Rated Current	10 A
Protection Class	IP20
Supply Voltage	200-480 VAC
Control Interface	EtherCAT, CANopen
Feedback Options	Resolver