Rohde & Schwarz FSVA - SENSe:ESPectrum Subsystem

Remote Control
R&S
®
FSVA/FSV
793Operating Manual 1176.7510.02 ─ 09
A video trigger is automatically activated with the same level as the squelch level, any
other trigger or gate settings are deactivated.
This command in only available if the R&S FSVA/FSV option B3 (Audio Demodulation)
is installed.
Parameters:
<State> ON | OFF
*RST: OFF
Example:
DEM:SQU ON
Signals below the level threshold are not sent to the audio out-
put.
Usage: SCPI confirmed
Manual operation: See "Squelch" on page 291
SENSe:ESPectrum Subsystem
The SENSe:ESPectrum subsystem contains the remote commands to configure
Spectrum Emission Mask (SEM) measurements.
The sweep list cannot be configured using remote commands during an on-going
sweep operation.
[SENSe:]ESPectrum:BWID............................................................................................. 794
[SENSe:]ESPectrum:FILTer[:RRC][:STATe]......................................................................794
[SENSe:]ESPectrum:FILTer[:RRC]:ALPHa....................................................................... 794
[SENSe:]ESPectrum:HighSPeed..................................................................................... 795
[SENSe:]ESPectrum:PRESet[:STANdard]........................................................................ 795
[SENSe:]ESPectrum:PRESet:RESTore............................................................................796
[SENSe:]ESPectrum:PRESet:STORe.............................................................................. 796
[SENSe:]ESPectrum:RANGe<range>:BANDwidth[:RESolution].......................................... 796
[SENSe:]ESPectrum:RANGe<range>:BANDwidth:VIDeo................................................... 797
[SENSe:]ESPectrum:RANGe<range>:COUNt................................................................... 797
[SENSe:]ESPectrum:RANGe<range>:DELete...................................................................797
[SENSe:]ESPectrum:RANGe<range>:FILTer:TYPE...........................................................797
[SENSe:]ESPectrum:RANGe<range>[:FREQuency]:STARt................................................798
[SENSe:]ESPectrum:RANGe<range>[:FREQuency]:STOP................................................ 799
[SENSe:]ESPectrum:RANGe<range>:INPut:ATTenuation..................................................799
[SENSe:]ESPectrum:RANGe<range>:INPut:ATTenuation:AUTO........................................ 799
[SENSe:]ESPectrum:RANGe<range>:INPut:GAIN:STATe..................................................800
[SENSe:]ESPectrum:RANGe<range>:INSert.................................................................... 800
[SENSe:]ESPectrum:RANGe<range>:LIMit<source>:ABSolute:STARt................................ 801
[SENSe:]ESPectrum:RANGe<range>:LIMit<source>:ABSolute:STOP.................................801
[SENSe:]ESPectrum:RANGe<range>:LIMit<source>:RELative:STARt.................................801
[SENSe:]ESPectrum:RANGe<range>:LIMit<source>:RELative:STOP................................. 802
[SENSe:]ESPectrum:RANGe<range>:LIMit<source>:STATe..............................................802
[SENSe:]ESPectrum:RANGe<range>:RLEVel...................................................................803
[SENSe:]ESPectrum:RANGe<range>:SWEep:TIME..........................................................803
Remote Control – Commands