Roland SonicCell User Manual

198
Effects List
A phaser that continues raising/lowering the frequency at
which the sound is modulated.
fig.MFX-14
This is an effect that applies amplitude modulation (AM) to the
input signal, producing bell-like sounds. You can also change
the modulation frequency in response to changes in the
volume of the sound sent into the effect.
fig.MFX-15
This is a ring modulator that uses a 16-step sequence to vary
the frequency at which modulation is applied.
fig.MFX-16
You can use multi-effect control to make the step sequence play
again from the beginning (p. 193).
Cyclically modulates the volume to add tremolo effect to the
sound.
fig.MFX-17a
14:
INFINITE PHASER
Parameter
Range Explanation
Mode 1, 2, 3, 4
Higher values will produce a
deeper phaser effect.
Speed # -100– +100
Speed at which to raise or lower
the frequency at which the sound
is modulated
(+: upward / -: downward)
Resonance # 0–127
Amount of feedback
Mix # 0–127
Volume of the phase-shifted
sound
Pan # L64–63R
Panning of the output sound
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Level 0–127
Output volume
15:
RING MODULATOR
Parameter
Value Description
Frequency # 0–127
Adjusts the frequency at which modulation is
applied.
Sens # 0–127
Adjusts the amount of frequency modulation
applied.
Polarity UP, DOWN
Determines whether the frequency modula-
tion moves towards higher frequencies ( UP )
or lower frequencies ( DOWN ).
Low Gain -15– +15 dB
Gain of the low frequency range
High Gain -15– +15 dB
Gain of the high frequency range
Balance #
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)
Level 0–127
Output level
Infinite Phaser 2-Band EQ
L in
R in
L out
R out
Pan R
Pan L
L in
R in
L out
R out
Ring Mod
2-Band EQ
2-Band EQ
Ring Mod
16:
STEP RING MOD
(STEP RING MODULATOR)
Parameter
Range Explanation
Step 01–16 0–127
Frequency of ring modulation at
each step
Rate # 0.05–10.00 Hz, note
Rate at which the 16-step sequence
will cycle
Attack # 0–127
Speed at which the modulation fre-
quency changes between steps
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Balance # D100:0W–D0:100W
Volume balance of the original
sound (D) and effect sound (W)
Level 0–127
Output volume
17:
TREMOLO
Parameter
Value Description
Mod Wave
TRI, SQR, SIN, SAW1,
SAW2
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
Rate # 0.05–10.00 Hz, note
Frequency of the change
Depth # 0–127
Depth to which the effect is applied
Low Gain -15– +15 dB
Gain of the low range
High Gain -15– +15 dB
Gain of the high range
Level 0–127
Output Level
L in
R in
L out
R out
Step Ring Mod
2-Band EQ
2-Band EQ
Step Ring Mod
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
SAW1 SAW2
SonicCell_e.book 198 ページ ２００７年８月９日 木曜日 午後９時１７分

Roland SonicCell Specifications

General

Brand	Roland
Model	SonicCell
Category	Computer Hardware
Language	English