Roland SonicCell User Manual

208
Effects List
This delay connects two delay units in series. Feedback can be
applied independently to each delay unit, allowing you to
produce complex delay sounds.
fig.MFX-45
Adds modulation to the delayed sound.
When Feedback Mode is NORMAL:
fig.MFX-46a
When Feedback Mode is CROSS:
fig.MFX-46b
45:
SERIAL DELAY
Parameter
Range Explanation
Delay1 Time 0–1300 ms, note
Delay time from when sound is
input to delay 1 until the delay
sound is heard
Delay1
Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the input
of delay 1 (negative values invert
the phase)
Delay1 HF Damp
200–8000 Hz,
BYPASS
Frequency at which the high-fre-
quency content of the delayed
sound of delay 1 will be cut (BY-
PASS: no cut)
Delay2 Time 0–1300 ms, note
Delay time from when sound is
input to delay 2 until the delay
sound is heard
Delay2
Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the input
of delay 2 (negative values invert
the phase)
Delay2 HF Damp
200–8000 Hz,
BYPASS
Frequency at which the high-fre-
quency content of the delayed
sound of delay 2 will be cut (BY-
PASS: no cut)
Pan # L64–63R
Panning of the delay sound
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Balance # D100:0W–D0:100W
Volume balance of the original
sound (D) and delay sound (W)
Level 0–127
Output volume
R in
R out
L in
L out
Feedback 1
Pan L
Pan R
Delay 1
Feedback 2
Delay 2
46:
MOD DELAY (MODULATION DELAY)
Parameter
Value Description
Delay Left
0–1300 ms,
note
Adjusts the time until the delay sound is
heard.
Delay Right
Feedback
Mode
NORMAL,
CROSS
Selects the way in which delay sound is fed
back into the effect (See the figures above.)
Feedback # -98– +98%
Adjusts the amount of the delay sound
that’s fed back into the effect. Negative (-)
settings invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you
don’t want to filter out any high frequen-
cies, set this parameter to BYPASS.
Rate #
0.05–10.00 Hz,
note
Frequency of modulation
Depth 0–127
Depth of modulation
Phase 0-180 deg
Spatial spread of the sound
Low Gain -15– +15 dB
Gain of the low frequency range
High Gain -15– +15 dB
Gain of the high frequency range
Balance #
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the delay sound (W)
Level 0–127
Output level
R in R out
L in L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
SonicCell_e.book 208 ページ ２００７年８月９日 木曜日 午後９時１７分

Roland SonicCell Specifications

General

Brand	Roland
Model	SonicCell
Category	Computer Hardware
Language	English