Roland SonicCell - Page 210

210
Effects List
This is a reverse delay that adds a reversed and delayed
sound to the input sound. A tap delay is connected
immediately after the reverse delay.
fig.MFX-50
Adds a shuffle to the delay sound, giving the sound a bouncy
delay effect with a swing feel.
fig.MFX-51
50:
REVERSE DELAY
Parameter
Range Explanation
Threshold 0–127
Volume at which the reverse de-
lay will begin to be applied
Rev Dly Time 0–1300 ms, note
Delay time from when sound is
input into the reverse delay until
the delay sound is heard
Rev Dly Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the input
of the reverse delay (negative
values invert the phase)
Rev Dly HF Damp
200–8000 Hz,
BYPASS
Frequency at which the high-fre-
quency content of the reverse-de-
layed sound will be cut (BYPASS:
no cut)
Rev Dly Pan L64–63R
Panning of the reverse delay
sound
Rev Dly Level 0–127
Volume of the reverse delay
sound
Delay 1 – 3 Time 0–1300 ms, note
Delay time from when sound is
input into the tap delay until the
delay sound is heard
Delay 3 Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the input
of the tap delay (negative values
invert the phase)
Delay HF Damp 200–8000 Hz, BYPASS
Frequency at which the low-fre-
quency content of the tap delay
sound will be cut (BYPASS: no
cut)
Delay 1 Pan’,
‘Delay 2 Pan
L64–63R
Panning of the tap delay sounds
Delay 1 Level’,
‘Delay 2 Level
0–127
Volume of the tap delay sounds
Low Gain -15– +15 dB
Amount of boost/cut for the low-
frequency range
High Gain -15– +15 dB
Amount of boost/cut for the high-
frequency range
Balance # D100:0W–D0:100W
Volume balance of the original
sound (D) and delay sound (W)
Level 0–127
Output volume
Feedback
L in
R in
Rev. Delay
L out
R out
2-Band
EQ
2-Band
EQ
Rev
Delay
D2
D1
D3
51:
SHUFFLE DELAY
Parameter
Value Description
Delay Time #
0–2600 ms,
note
Adjusts the time until the delay sound is
heard.
Shuffle
Rate #
0–100%
Adjusts the ratio (as a percentage) of the
time that elapses before Delay B sounds rel-
ative to the time that elapses before the De-
lay A sounds.
When set to 100%, the delay times are
the same.
Acceleration 0–15
Adjusts the speed which the Delay Time
changes from the current setting to its speci-
fied new setting.
Feedback # -98– +98%
Adjusts the amount of the delay that’s fed
back into the effect. Negative (-) settings in-
vert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which sound
fed back to the effect is filtered out. If you
don’t want to filter out any high frequencies,
set this parameter to BYPASS.
Pan A/B 0–127
Stereo location of Delay A/B
Level A/B 0–127
Volume of delay A/B
Low Gain -15– +15 dB
Gain of the low frequency range
High Gain -15– +15 dB
Gain of the high frequency range
Balance #
D100:0W–
D0:100W
Volume balance between the direct sound
(D) and the effect sound (W)
Level 0–127
Output level
Feedback
L in
R in
Delay
L out
R out
2-Band
EQ
2-Band
EQ
A
B
Delay A
Delay B
SonicCell_e.book 210 ページ ２００７年８月９日 木曜日 午後９時１７分