8
Using the Internal Clock to Trigger Sequences ............................................................................ 50
4.5.1.4.
Setting Up Control Inputs for a Sequence ..................................................................................... 53 4.5.1.5.
Setting Up Control Outputs for a Sequence .................................................................................. 54 4.5.1.6.
Setting the Progress Reporting Mode for the Sequences ............................................................. 55 4.5.1.7.
Adding Sequence Steps ........................................................................................................................ 56 4.5.2.
The GENERATE Step .................................................................................................................... 57 4.5.2.1.
The STANDBY Step ...................................................................................................................... 58 4.5.2.2.
The DURATION Step ..................................................................................................................... 58 4.5.2.3.
The EXECSEQ Step ...................................................................................................................... 59 4.5.2.4.
The CC OUTPUT Step .................................................................................................................. 60 4.5.2.5.
Deleting or Editing an Individual Step in a Sequence .................................................................... 61 4.5.2.6.
Deleting a Sequence ............................................................................................................................. 62 4.5.3.
4.6. SETUP > CFG ............................................................................................................................................. 63
4.7. SETUP > CLK .............................................................................................................................................. 64
Setting the Internal Clock‟s Time and Day ............................................................................................ 64
4.7.1.
Adjusting the Internal Clock‟s speed ..................................................................................................... 65 4.7.2.
4.8. SETUP > PASS ........................................................................................................................................... 66
4.9. SETUP > DIAG > TEST CHAN OUTPUT: Using the TEST Channel Analog Output ................................. 68
Configuring the TEST Channel Analog Output ..................................................................................... 68 4.9.1.
The Analog I/O Configuration Submenu ........................................................................................ 68 4.9.1.1.
Selecting a TEST Channel Function to Output .............................................................................. 70 4.9.1.2.
TEST Channel Voltage Range Configuration ................................................................................ 72 4.9.1.3.
Turning the TEST Channel Over-Range Feature ON/OFF ........................................................... 73 4.9.1.4.
Adding a Recorder Offset to the TEST Channel ............................................................................ 74 4.9.1.5.
TEST Channel Calibration ..................................................................................................................... 75 4.9.2.
Enabling or Disabling the TEST CHANNEL Auto-Cal Feature ...................................................... 76 4.9.2.1.
Automatic TEST Channel Calibration ............................................................................................ 77 4.9.2.2.
Manual Calibration of the TEST Channel Configured for Voltage Ranges ................................... 79 4.9.2.3.
AIN Calibration ...................................................................................................................................... 81
4.9.3.
4.10. SETUP > MORE > VARS: Internal Variables (VARS) .............................................................................. 82
4.11. Operating the Calibrator as an O
3
Photometer ......................................................................................... 83
Set up for Operation as an O
3
Photometer ......................................................................................... 84 4.11.1.
4.12. SETUP > LVL: Setting up and using LEADS (Dasibi) Operating Levels .................................................. 86
General Information about LEADS LEVELS ....................................................................................... 86 4.12.1.
Dot commands .................................................................................................................................... 86 4.12.2.
Levels .................................................................................................................................................. 86 4.12.3.
Activating an existing LEVEL .............................................................................................................. 87 4.12.4.
Programming New LEVELS ................................................................................................................ 88 4.12.5.
Creating a Generate LEVEL ........................................................................................................ 89 4.12.5.1.
Editing or Deleting a LEVEL ........................................................................................................ 90 4.12.5.2.
Configuring LEVEL Status Blocks ....................................................................................................... 91 4.12.6.
5. COMMUNICATIONS ........................................................................................................... 93
5.1. Using the Analyser‟s Communication Ports ................................................................................................ 93
RS-232 DTE and DCE Communication ................................................................................................ 93 5.1.1.
Serial COM Port Default Settings and Connector Pin Assignments ..................................................... 94 5.1.2.
COM Port Baud Rate ............................................................................................................................ 96 5.1.3.
COM Port Communication Modes ........................................................................................................ 96 5.1.4.
COM Port Testing .................................................................................................................................. 99 5.1.5.
Machine ID .......................................................................................................................................... 100 5.1.6.
Terminal Operating Modes .................................................................................................................. 101 5.1.7.
Help Commands in Terminal Mode ............................................................................................. 101 5.1.7.1.
Command Syntax ........................................................................................................................ 102 5.1.7.2.
Data Types ................................................................................................................................... 103 5.1.7.3.
Status Reporting .......................................................................................................................... 103 5.1.7.4.
General Message Format ............................................................................................................ 104 5.1.7.5.
COM Port Password Security ...................................................................................................... 104 5.1.7.6.
To Next Page
Loading...