Uson Qualitek mR - Page 162

8-6 Qualitek mR Owner’s Guide
1etalosI4
x
Isolates the test port .
1
1
cavE/lliF5 )erusserP eguaG kcehC( 2 ro 1 geR gnisu ezirusserPXXX
X
XX
1
2
cavE/lliF6 XXX
x
XX
1
erusaeM8 X XX
1
tneV
9
XX
02 elpu
o
c
nU01
XX/R
0
1
elp
u
o
c
nU11 X/R
EOC Return to Ready.
0
1 elpuoC1
X
0
2 elpuoC2 XX
x
orez otuA3
XX
1
1
cavE/lliF5 )eruss
erP eguaG
kc
ehC
(
2 ro 1 geR gnisu ezirusserPXXX
XX
1
2
cavE/lliF6
X
X
XXX
1erusaeM8
X
XX
1tneV9 XX
0
2 elpuocn
U01 XX/R
0
1 elpuocn
U11
X/R
EOC Return to Ready.
1
rosneS tneV1
2 Measure Sensor Output 1
0
ezilauqE egagnE1 X
2 Fill - Manual or Electronic 1
XXX
3 Measure Sensor Output 1
XXX
1rosneS tneV4
EOC Return to Ready.
2
rosneS tneV1
2 Measure Sensor Output 2
1 Pressurize Test Port 20 mbar 2 X
2 Measure Sensor Output 2 X
0rosneS tneV3
EOC Return to Ready.
0
1 e
lpuoC1 X
0
2 elpuoC2
XX
2orez otuA3 XX
1
1
cavE/lliF
4 X
X
XXX
1
2
cavE/lliF5 XX
XX
1ezilibatS6 X XX
2ezilauqE7 XXX
X
2erusaeM
8 XXXX
1
tneV9 XX
02 elpu
o
c
n
U01 XX/R
01 elpuocn
U
1
1
X/R
EOC Return to Ready.
Disengage Coupling Port 1
Disengage Coupling Port 1
EOC
Measure the resulting gauge pressure.
Exhaust
Disengage Coupling Port 2
Pressurize using Reg 1 or 2 (Check Gauge Pressure)
Test Sequence - Gauge Sensor Calibration - Zero
Vent
Measure Zero Output
EOC
Measure resulting gauge pressure.
Exhaust
Disengage Coupling Port 2
Measure Full-scale Output
Pressurize (Manual or Electronic)
Test Sequence - Differential Sensor Calibration - Span
Exhaust
EOC
Pressurize using Reg 1 or 2 (Check Gauge Pressure)
Vent
Measure Zero Output
Test Sequence - Differential Sensor Calibration - Zero
Exhaust
EOC
Pressurize (Externally to 20.0 mbar)
Measure Full-scale Output
Engage Coupling Port 2
Test Sequence - Seal Leak Test Cycl
e
Pressurize using Reg 1 or 2 (Check Gauge Pressure)
Test Sequence - Back Pressure Flo
w
Engage Coupling Port 1
Engage Coupling Port 2
Auto Zero Transducers
Test Sequence - Gauge Sensor Calibration - Span
Engage Equalize Valve
Disengage Coupling Port 1
EOC
Engage Coupling Port 1
Auto Zero Transducer
Exhaust
Disengage Coupling Port 2
Pressurize using Reg 1 or 2 (Check Gauge Pressure)
Stabilize (Gross Leak Gauge)
Equalize (Gross Leak Differential)
Fine Leak Test (pressure change/ tared value only)