February, 2008
6-36
WorkCentre 5225, 5230
IIT NVM List
Launch Version
General Procedures
715-310 A3/11x17 Detection 0 0~3 0: Table default 1: A3SEF 2: This value is for design test. Performance is not guaranteed. 3: A3SEF,
11x17SEF
715-311 A4/8.5x11 Detection 0 0~3 0: Table default 1: A4LEF 2: This value is for design test. Performance is not guaranteed. 3:
8.5x11LEF, A4LEF
715-312 A6S Threshold 90 50~110 Changes the threshold value in the fast scan direction between non-standard size paper, postcard
SEF, and A6 SEF. When values outside the setting range (50~100) are set, the threshold value in
the fast scan direction is 90mm. 50 ~ 100mm in 1mm increments.
715-344 Original Size Detection, Platen Background
Countermeasure for Dirt
0 0~1 0: Detection by 4 registers 1: Detection by 3 registers (countermeasure for dirt)
715-345 GCO/TFX Size Switch 1 0~1 0: GCO (16K/8K=270x195/270x390) 1: TFX (16K/8K=267x194/267x388)
715-346 B4/8K Fast Scan Threshold Value Setting 3 0~6 0: 256mm, 1: 258mm, 2: 260mm, 3: 262mm, 4: 264mm, 5: 266mm, 6: 268mm
715-347 8K/11x17SEF Fast Scan Threshold Value Setting 3 0~6 0: 269mm, 1: 271mm, 2: 273mm, 3: 275mm, 4: 277mm, 5: 279mm, 6: 281mm
715-349 B6/5x7 Detection 0 0~2 0: Table default 1: B6SEF 2: 5x7SEF
715-362 FL_CHK_NG_Count 0 0~65535 Lamp Check NG Count (Reset when lamp is replaced)
715-363 FL_CHK_NG_Data 0 0~1023 Data obtained when Lamp Check Fails (Read G Write data compared at checking)
715-418 AOCerr 0 0~255 Number of times the AOC flow has ended abnormally
715-550 TP_BW_Copy BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-551 TP_CL_Copy BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-552 TX_BW_Copy BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-553 TX_CL_Copy BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-554 TP_BW_Contone BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-555 TP_CL_Contone BGR-AE-Level 0 0~4095 Removal amount is “the value (0 to 15) X 3” (8-bit conversion). (For 10-bit conversion, “the value [0
to 15] X 12”.) Last 0 to 3 bits: Platen, 4 to 7 bits: CVT or machines with DADF, 8 to 11 bits: CVT or
machines with DADF (duplex copy)
715-560 BWPG Density 128 0~255 Solid PG density of the whole page (0: Black)
715-600 AE1 FS External Area 255 0~65535 High Speed AE/Fast Scan Direction undetected area INSTV At SMPST, SMPED setting
715-601 AE2 FS External Area 255 0~65535 High Speed AE/Fast Scan Direction undetected area INSTV At HAEFST, HAEFSE setting
715-602 AE3 FS External Area 255 0~65535 High Speed AE/Fast Scan Direction undetected area INSTV At MAEFST, MAEFSE setting (* Area
used as detection area is used for PreIPS noise removal as well)
715-603 AE4 FS External Area 255 0~65535 High Speed AE/Fast Scan Direction undetected area INSTV At NAEFST, NAEFSE setting
715-604 Line to Fix Variation 60 0~65535 High Speed AE/Slow Scan Direction variable fixed position/NCON Slow Scan Edge AE Detection
Amount (0.16mm increments)
715-605 HAE Line to Fix Variation 240 0~65535 End position for AE in the slow scan direction. Width in the slow scan direction for detecting back-
ground density with RAE. HAESSE
Table 2 IISS
Chain-Link Content Default Range Meaning
To Next Page
Loading...
Need help?
General
