H2 Multi-Function Digital Output Settings
H2-oo
Setting
Function Description Page
30 During torque limit
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLVV/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM
OLV
CLV/PM
CLV
Closed: When the torque limit has been reached.
225
31 During speed limit
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
Closed: Speed limit has been reached.
226
32
During speed limit in Torque
Control
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
Closed: Speed limit has been reached while using Torque Control.
226
33 Zero Servo complete
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
Closed: Zero Servo operation has finished.
226
37 During frequency output
All Modes
Open: Either the drive has stopped or baseblock, DC Injection Braking, or Initial Excitation is
being performed.
Closed: Drive is running the motor (not in a baseblock state and DC Injection is not being
performed).
226
38 Drive enabled
All Modes
Closed: Multi-function input set for “Drive enable” is closed (H1-oo = 6A).
226
39 Watt hour pulse output
All Modes
Output units are determined by H2-06. Outputs a pulse every 200 ms to indicate the kWh count.
226
3C LOCAL/REMOTE status
All Modes
Open: REMOTE
Closed: LOCAL
226
3D During speed search
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
Closed: Speed Search is being executed.
227
3E PID feedback low
All Modes
Closed: PID feedback level is too low.
227
3F PID feedback high
All Modes
Closed: The PID feedback level is too high.
227
4A During KEB Ride-Thru
All Modes
Closed: KEB Ride-Thru is being performed.
227
4B During short circuit braking
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
Closed: Short Circuit Braking is active.
227
4C During fast stop
All Modes
Closed: A Fast Stop command has been entered from the operator or input terminals.
227
4D oH Pre-alarm time limit
All Modes
Closed: oH pre-alarm time limit has passed.
227
4E Braking transistor fault (rr)
All Modes
Closed: The built-in dynamic braking transistor failed.
227
4F Braking resistor overheat (oH)
All Modes
Closed: The dynamic braking resistor has overheated.
227
60 Internal cooling fan alarm
All Modes
Closed: Internal cooling fan alarm
227
61
Rotor position detection
complete
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM CLV/PM
V/f
OLV/PM
V/f w PG
AOLV/PM
OLV
CLV/PM
CLV
AOLV/PM CLV/PM
Closed: Drive has successfully detected the rotor position of the PM motor.
227
B.9 H Parameters: Multi-Function Terminals
YASKAWA ELECTRIC SIEP C710616 31B YASKAWA AC Drive – A1000 Technical Manual
421
B
Parameter List
To Next Page
Loading...
