Brother HL-S7000DN - Page 173

3-5
Confidential
Cap motor cover Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Sub tank ASSY Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
Head attachment of the
Pre-coat head
Screw pan (P) M2P0.4x18 2 0.15±0.02 (1.5±0.2)
Head attachment of the Ink
head
Screw pan (P) M2P0.4x18 2 0.15±0.02 (1.5±0.2)
Fan unit Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Pre-coat duct Taptite cup S M3x6 SR 1 0.8±0.1 (8±1)
Ink duct Taptite cup S M3x6 SR 1 0.8±0.1 (8±1)
Ink head ASSY Flange nut M3 2 1.1±0.1 (11±1)
Taptite cup B M3x10 3 0.5±0.1 (5±1)
Pre-coat head ASSY Flange nut M3 2 1.1±0.1 (11±1)
Taptite cup B M3x10 3 0.5±0.1 (5±1)
Head protector Screw bind M2x16 2 0.15±0.02 (1.5±0.2)
Cover frame rear L Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
Buffer tank ASSY Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Tube holder bracket Taptite cup S M3x6 SR 1 0.8±0.1 (8±1)
Drive frame ASSY Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
Main PCB shield plate Taptite cup S M3x6 SR 6 0.4±0.1 (4±1)
Main PCB ASSY Taptite cup S M3x6 SR 4 0.4±0.1 (4±1)
Speaker holder Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Paper feed PCB ASSY Taptite cup S M3x6 SR 2 0.4±0.1 (4±1)
Power supply PCB ASSY Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
Paper eject ASSY Taptite cup S M4x8 4 1.0±0.1 (10±1)
Carriage unit Taptite cup S M4x8 8 1.0±0.1 (10±1)
Eject tray guide ASSY Taptite bind B M4x10 3 0.8±0.1 (8±1)
PF drive gear ASSY Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
Platen unit Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
Carriage encoder sensor
ASSY
Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
ID key holder Taptite cup B M3x8 2 0.5±0.1 (5±1)
LT front cover Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
LT side cover R Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
LT relay shield plate Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
Location of screw Screw type Q' ty
Tightening torque
N
·m (kgf·cm)