Brother HL-S7000DN - Page 174

3-6
Confidential
LT relay PCB ASSY Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
ID switch holder Taptite cup S M3x8 SR 1 0.8±0.1 (8±1)
LT side cover L Taptite cup S M3x8 SR 2 0.8±0.1 (8±1)
LT back cover Taptite cup S M3x8 SR 2 0.8±0.1 (8±1)
Tray guide R back Taptite cup S M3x8 SR 2 0.8±0.1 (8±1)
Size SW spring Taptite cup S M3x8 SR 3 0.8±0.1 (8±1)
Size SW PCB ASSY Taptite cup S M3x8 SR 1 0.8±0.1 (8±1)
Upper plate Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Clutch hold plate Taptite cup S M3x8 SR 2 0.8±0.1 (8±1)
LT lock L ASSY Taptite cup S M3x8 SR 4 0.8±0.1 (8±1)
LT feed plate 2 Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
PF drive plate Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
LT guide plate Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
LT beam F sub ASSY Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
Paper feed jam sensor PCB
ASSY
Taptite bind B M3x8 1 0.5±0.1 (5±1)
LT beam F Taptite cup B M3x8 3 0.5±0.1 (5±1)
Gear plate Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
LT beam M Taptite cup S M3x6 SR 4 0.8±0.1 (8±1)
LT frame L Taptite bind B M4x10 2 0.8±0.1 (8±1)
Paper empty sensor PCB
holder
Taptite cup B M3x8 1 0.5±0.1 (5±1)
FG harness Taptite cup S M3x6 SR 1 0.8±0.1 (8±1)
LT frame L Taptite bind B M4x10 3 0.8±0.1 (8±1)
Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
LT frame R Taptite bind B M4x10 3 0.8±0.1 (8±1)
Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Stacker top Taptite cup S M3x6 SR 2 0.8±0.1 (8±1)
Stacker side L Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
Stacker side R Taptite cup S M3x6 SR 3 0.8±0.1 (8±1)
Stacker eject top cover Taptite cup B M3x8 4 0.4±0.1 (4±1)
Stacker front under Taptite cup B M3x8 2 0.4±0.1 (4±1)
Stacker tray ASSY Taptite cup B M3x6 2 0.4±0.1 (4±1)
Stacker tray A Taptite cup B M3x8 4 0.4±0.1 (4±1)
Location of screw Screw type Q' ty
Tightening torque
N
·m (kgf·cm)