D-Link xStack - Create Cfm MD

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
239
<uint 1-4294967295>] mepid <int 1-8191> {period [1sec | 1min] | level <int 0-7> | state
[enable | disable]}
config cfm lock md [<string 22> | md_index <uint 1-4294967295>] ma [<string 22> | ma_index
<uint 1-4294967295>] mepid <int 1-8191> {period [1sec | 1min] | level <int 0-7> | state
[enable | disable]}
config cfm trap [ais | lock] state [enable | disable]
cfm dm <macaddr> [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint
1-4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]] {period:interval
[100ms:1sec | 1sec:10sec | 10sec:1min] | percentile <int 0-100> | pdu_priority <int 0-7>}
cfm lm <macaddr> [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint
1-4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]] {period [100ms | 1sec |
10sec] | pdu_priority <int 0-7>}
clear cfm dm {[mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]]} {[results | statistics]}
clear cfm lm {[mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]]} {[results | statistics]}
config cfm dm [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]] state [enable | disable]
config cfm lm [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]] state [enable | disable]
show cfm dm [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]]
show cfm lm [mepname <string 32> | mepid <int 1-8191> md [<string 22> | md_index <uint 1-
4294967295>] ma [<string 22> | ma_index <uint 1-4294967295>]]
16-1 create cfm md
Description
This command is used to create a CFM maintenance domain.
Format
create cfm md <string 22> {md_index <uint 1-4294967295>} level <int 0-7>
Parameters
<string 22> - Enter the maintenance domain name used here. This name can be up to 22
characters long.
md_index - Specifies the maintenance domain index used.
<uint 1-4294967295> - Enter the maintenace domain index value used here. This value must
be between 1 and 4294967295.
level - Specifies the maintenance domain level.
<int 0-7> - Enter the maintenance domain level from 0 to 7.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only
Command)
Example
To create a CFM maintenance domain called “op_domain” and assign a maintenance domain level
of “2”: