D-Link xStack - Page 577

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
572
4294967294> | route_type [internal | external | type_1 | type_2] | interface <ipif_name 12> |
route_source <list_name 16>] | set [add | delete] [next_hop [<ipaddr> | peer_address] |
metric <uint 0-4294967294> | local_preference <uint 0-4294967295> | weight <value 0-
65535> | as_path <aspath_list> | community {community_set <community_set 80> | internet
| no_export | no_advertise | local_as} {additive} | origin [egp | igp | incomplete] | dampening
<min 1-45> <value 1-20000> <value 1-20000> <min 1-255> <min 1-45> | metric_type [type_1 |
type_2]]]]
Parameters
<map_name 16> - Enter the route map name used here. This name can be up to 16 characters
long.
add - Specifies to add a sequence entry.
delete - Specifies to remove a sequence entry.
sequence - Specifies the sequence number for the route map rule.
<value 1-65535> - Enter the sequence number used here. This value must be between 1 and
65535.
deny - (Optional) Specifies to deny the route if the rule is matched.
permit - (Optional) Specifies to permit the route if the rule is matched.
sequence - Specifies the sequence number for the route map rule.
<value 1-65535> - Enter the sequence number used here. This value must be between 1 and
65535.
match - Specifies to check if the sequence entry matches.
add - Specifies the entry or the set to add.
delete - Specifies the entry or the set to delete.
as_path - Specifies to match the AS path of the route against the AS path list. The AS path list
specified here needs to be a sub-list of the AS path list associated with the route.
<list_name 16> - Enter the AS path name used here. This name can be up to 16 characters
long.
community_list - Specifies to match the community of the route against the community string.
<list_name 16> - Enter the community list name used here. This name can be up to 16
characters long.
exact - (Optional) Specifies that all of the communities and only those communities specified
must be present.
ip - Specifies to match the route according to the access list.
next_hop - Specifies to match the next hop of the route according to the access list.
address - Specifies to match the route according to the access list.
prefix_list - (Optional) Specifies to match the route according to the prefix list.
<list_name 16> - Enter the prefix list name used here. This name can be up to 16
characters long.
metric - Specifies to match the metric of the route.
<uint 0-4294967294> - Enter the metric value used here. This value must be between 0 and
4294967294.
route_type - Specifies to match the type of the imported route.
internal - Specifies an OSPF AS-internal route.
external - Specifies an OSPF AS-external route, including type-1 and type-2.
type_1 - Specifies an OSPF AS-external type-1 route.
type_2 - Specifies an OSPF AS-external type-2 route.
interface - Specifies to match the outgoing interface of the imported route.
<ipif_name 12> - Enter the outgoing interface name. This name can be up to 12 characters
long.
route_source - Specifies to match the source of the imported route.
<list_name 16> - Enter the route source name. This name can be up to 16 characters long.
set - Specifies to define the conditions for redistributing routes from one routing protocol into
another.
add - Specifies the set to add.
delete - Specifies the set to delete.
next_hop - Specifies the next hop attribute.