Fujitsu Server PRIMERGY TX1330 M1 User Manual

Upgrade and Maintenance Manual TX1330 M1
Content
9.5.7 Replacing a BBU . . . . . . . . . . . . . . . . . . . . . . . . 206
9.5.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 206
9.5.7.2 Removing the defective BBU . . . . . . . . . . . . . . . . 206
9.5.7.3 Installing the new BBU . . . . . . . . . . . . . . . . . . . 208
9.5.7.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 208
10 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . 209
10.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 209
10.1.1 Memory sequence . . . . . . . . . . . . . . . . . . . . . . . 210
10.1.2 Operation modes . . . . . . . . . . . . . . . . . . . . . . . . 211
10.2 Removing memory modules . . . . . . . . . . . . . . . . . 211
10.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 211
10.2.2 Removing a memory module . . . . . . . . . . . . . . . . . . 212
10.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 212
10.3 Installing memory modules . . . . . . . . . . . . . . . . . . 213
10.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 213
10.3.2 Installing a memory module . . . . . . . . . . . . . . . . . . . 213
10.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 214
10.4 Replacing memory modules . . . . . . . . . . . . . . . . . 214
10.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 214
10.4.2 Removing the defective memory module . . . . . . . . . . . . 215
10.4.3 Installing the new memory module . . . . . . . . . . . . . . . 215
10.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 215
11 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
11.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 218
11.2 Upgrading or replacing the processor . . . . . . . . . . . . 218
11.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 218
11.2.2 Removing the processor heat sink . . . . . . . . . . . . . . . 219
11.2.3 Removing the processor . . . . . . . . . . . . . . . . . . . . 220
11.2.4 Installing the processor . . . . . . . . . . . . . . . . . . . . . 221
11.2.5 Applying thermal paste . . . . . . . . . . . . . . . . . . . . . 223
11.2.6 Installing the processor heat sink . . . . . . . . . . . . . . . . 225
11.2.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 227
11.3 Replacing the processor heat sink . . . . . . . . . . . . . . 227
11.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 227

Fujitsu Server PRIMERGY TX1330 M1 Specifications

General

Memory Slots	4
Form Factor	Tower
Chipset	Intel C226
Processor Sockets	1
Processor	Intel Pentium, Intel Celeron
RAID Support	RAID 0, 1, 5, 10
Drive Bays	8 x 3.5-inch
Operating System Support	Windows Server, Red Hat, SUSE, VMware

Summary

Before Reading This Manual

For Your Safety

Provides essential safety information for using the product.

1 Introduction

1.1 Notational Conventions

Explains symbols and formatting used in the manual.

2 Before You Start

2.1 Classification of Procedures

Categorizes procedures by complexity and required skills.

2.3 Tools You Need at Hand

Lists required tools for performing maintenance.

2.4 Documents You Need at Hand

Lists essential manuals for reference.

3 Important Information

3.1 Safety Instructions

Critical safety guidelines for installation and operation.

3.2 ENERGY STAR

Information on ENERGY STAR compliance.

3.3 CE Conformity

Details on compliance with EC directives.

3.4 FCC Class A Compliance Statement

Statement regarding FCC Class A emissions.

4 Basic Hardware Procedures

4.1 Using Diagnostics Information

Guidance on using diagnostic tools for troubleshooting.

4.2 Shutting Down the Server

Step-by-step instructions for server shutdown.

4.4 Getting Access to the Component

Instructions for accessing internal server components.

5 Basic Software Procedures

5.1 Starting the Maintenance Task

Preparatory software steps before hardware maintenance.

5.2 Completing the Maintenance Task

Post-maintenance software configuration and checks.

6 Power Supply

6.1 Basic Information

Overview of power supply configurations.

6.2 Standard Power Supply

Information and procedures for the standard power supply unit.

6.3 Redundant Power Supply

Information and procedures for redundant power supply units.

6.4 Converting a Standard Power Supply to a Redundant Power Supply

Steps to upgrade from standard to redundant PSU.

7 Hard Disk Drives / Solid State Drives

7.1 Basic Information

Overview of HDD/SSD configurations.

7.2 2.5-inch HDD / SSD Configurations

Details on installing and managing 2.5-inch drives.

7.3 3.5-inch HDD Configurations

Details on installing and managing 3.5-inch drives.

8 System Fan and Air Duct

8.1 Basic Information

Overview of the system fan module.

8.2 Handling the Fan Module

Procedures for managing the system fan module.

8.3 Replacing the System Fan

Step-by-step guide for replacing the system fan.

9 Expansion Cards and Backup Units

9.1 Basic Information

Overview of system board expansion slots.

9.4 Expansion Cards and Riser Card

Procedures for installing and removing expansion cards.

9.5 Backup Units

Procedures for installing and replacing backup units.

10 Main Memory

10.1 Basic Information

Details on supported memory modules and capacities.

10.3 Installing Memory Modules

Procedure to install memory modules.

10.4 Replacing Memory Modules

Procedure to replace memory modules.

11 Processors

11.1 Basic Information

Details on supported CPUs.

11.2 Upgrading or Replacing the Processor

Procedure for processor replacement.

12 Accessible Drives

12.1 Basic Information

Overview of accessible drive bays.

12.2 Installing Accessible Drives

Procedures for installing accessible drives.

12.3 Removing Accessible Drives

Procedures for removing accessible drives.

12.4 Replacing Accessible Drives

Procedure for replacing accessible drives.

13 Front Panel Module

13.1 Replacing the Front Panel Module

Procedure for replacing the front panel module.

14 System Board and Components

14.1 Basic Information

Overview of system board components.

14.2 Replacing the CMOS Battery

Procedure to replace the CMOS battery.

14.5 Replacing the System Board

Step-by-step guide for replacing the system board.

15 Converting a Tower Model to a Rack Model

15.1 Preliminary Steps

Initial steps for the conversion process.

15.2 Converting a Tower Model to a Rack Model

Detailed steps for the physical conversion.

15.3 Concluding Steps

Final steps after conversion.

16 Cabling

16.1 List of Used Cables

Inventory of cables and their routing.

16.2 Cabling Plans

Diagrams showing cable connections.

16.3 Replacing the Intrusion Switch Cable

Procedure for replacing the intrusion switch cable.

17 Appendix

17.1 Mechanical Overview

Diagrams of server layout and components.

17.2 Connectors and Indicators

Details on system board and I/O panel connectors and indicators.

17.4 Minimum Startup Configuration

Steps for configuring the server to a basic state.