Huawei Quidway S9300

[SwitchC-nqa-admin-mtrace] test-type mtrace
[SwitchC-nqa-admin-mtrace] mtrace-source-address ipv4 11.1.0.2
[SwitchC-nqa-admin-mtrace] mtrace-group-address ipv4 225.1.1.1
[SwitchC-nqa-admin-mtrace] destination-address ipv4 11.1.6.4
[SwitchC-nqa-admin-mtrace] mtrace-query-type destination
Step 2 Perform the test.
[SwitchC-nqa-admin-mtrace] start now
Step 3 Verify the test result. You can find that the RPF path from the multicast source to Switch C is
Switch E-Switch D-Switch C.
[SwitchC-nqa-admin-mtrace] display nqa results test-instance admin mtrace
NQA entry(admin, mtrace) :testFlag is inactive ,testtype is mtrace
1 . Test 1 result The test is finished
Completions: success Query Mode: max-hop
Current Hop:3 Current Probe:1
SendProbe:1 ResponseProb:1
Timeout Count:0 Busy Count:0
Drop Count:0 Max Path Ttl:4
Responser:11.1.2.2 Response Rtt: 83
mtrace start time: 2009-2-7 17:26:53.2
Last Good Probe Time: 2009-2-7 17:26:53.3
Last Good Path Time: 2009-2-7 17:26:53.3
1 . Hop 1
Outgoing Interface Address: 11.1.6.2
Incoming Interface Address: 11.1.4.1
Prehop Router Address: 11.1.4.2
Protocol : PIM Forward Code:NO_ERROR
Forward Ttl:1 Current Path Ttl:4
SG Packet Count:255 Hop Time Delay(ms): 0xffffffff
Input Packet Count:9207 Output Packet Count:9596
Input Rate(pps): 0xffffffff Output Rate(pps): 0xffffffff
Input Loss Rate: 0xffffffff SG Loss Rate: 0xffffffff
2 . Hop 2
Outgoing Interface Address: 11.1.4.2
Incoming Interface Address: 11.1.2.1
Prehop Router Address: 11.1.2.2
Protocol : PIM Forward Code:NO_ERROR
Forward Ttl:1 Current Path Ttl:3
SG Packet Count:255 Hop Time Delay(ms):327
Input Packet Count:9627 Output Packet Count:9222
Input Rate(pps): 0xffffffff Output Rate(pps): 0xffffffff
Input Loss Rate: 0xffffffff SG Loss Rate: 0xffffffff
3 . Hop 3
Outgoing Interface Address: 11.1.2.2
Incoming Interface Address: 11.1.0.1
Prehop Router Address: 0.0.0.0
Protocol : PIM Forward Code:NO_ERROR
Forward Ttl:1 Current Path Ttl:2
SG Packet Count:0 Hop Time Delay(ms): 0xffffffff
Input Packet Count:105129 Output Packet Count:16320
Input Rate(pps): 0xffffffff Output Rate(pps): 0xffffffff
Input Loss Rate: 0xffffffff SG Loss Rate: 0xffffffff
----End
Configuration Files
l Configuration file of Switch A
#
sysname SwitchA
#
multicast routing-enable
#
vlan batch 110 170
#
Quidway S9300 Terabit Routing Switch
Configuration Guide - Network Management 6 NQA Configuration
Issue 03 (2010-09-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6-201