Operation
158
Pos: 48.97.8 /Üb erschriften/Üb erschriften 3/K- O/N/Netzrolle ei nlegen @ 2 98\mod_141276 5877831_78. docx @ 2335075 @ 3 @ 1
11.18.2 Inserting Net Roll
Pos: 48.97.9 /B A/Sicherheit/8. V oraussetzungen /Handlungsan weisung für all e Maschinen/Vora ussetzung: Die Maschine ist stil lgesetzt u nd gesichert, .... @ 259\mod _139867443417 0_78.docx @ 19 79947 @ @ 1
Prerequisite:
– Shut down and safeguard the machine, see chapter Safety, "Shutting down and
safeguarding the machine".
Pos: 48.97.10 / Beipacks/Rundball enpressen/Folie nbindung/M odulgruppen Foli e einlegen / L ED Lichtleiste/Netzr olle einlegen _Netz- od er Folienrolle ei nlegen_Bild_Netz bindung oder Folienbindung @ 507\mod_ 15003598786 44_78.docx @ 348 5579 @ @ 1
Fig.
Pos: 48.97.11 / BA/Bedienung /R undballenpresse/N etzbindung _nur Ausführ ung Netzbindung ab 17 18/Netzr olle einlegen_T ext @ 507\ mod_15002903 20419_78.doc x @ 3484570 @ @ 1
• Raise the lever (4).
• Swing the roll holder (6) and brake disc (1) forward.
• Detach the brake disc (1).
• Take a new net roll from the package. Make sure that the beginning of the net roll faces
towards the machine and can be pulled out from above.
• Push the net roll (9) on the roll holder (6) and push the holder (7) on.
• Slide the brake disc (1) and cardboard tube clamp (2) anticlockwise into the cardboard
tube (10) of the net roll (9) as far as it will go.
The net roll (9) is permanently locked in the roll holder (6).
• Swing the roll holder (6) back into the machine and raise it into the lock by means of the
lever (4).
• Actuate the wrapping material brake lever (3) so that the roll holder (6) snaps home at the
wrapping material brake.
• When swinging the roll holder back, ensure that the clamping lever 5) is under the net
roll (9).
• Check that the net roll (9) is aligned centrally. To do so, measure the distance dimensions
to the left and right side walls.
Pos: 48.97.12 / BA/Bedienung /R undballenpresse/N etzbindung _nur Ausführung N etzbindung a b 17 18/Netz- /Folienroll e einlegen_Bild 2 @ 507\mod_ 15002915854 75_78.docx @ 3484634 @ @ 1
Fig.
Pos: 48.97.13 / BA/Bedienung /R undballenpres se/Netzbindu ng_nur Ausführ ung Netzbindung ab 17 18/Netzr olle einlegen_T ext2 @ 507 \mod_1500291 680040_78.docx @ 3484665 @ @ 1
If the net roll (9) has still not been centrally aligned:
• Loosen the two adjusting rings (8, 11).
• Use a mounting lever (12) to push the net roll (9) in the desired direction shown by the
arrow until the net roll (9) is positioned in the centre.
• Push the two adjusting rings (8, 11) with a distance dimension each of 2-3 mm towards the
inner cardboard tube (10) and fix them in this position.
Pos: 48.97.14 / Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196 175311226_0. docx @ 4165 @ @ 1
To Next Page
Loading...
