Commissioning
83
Pos: 40.39.1 /Üb erschriften/Üb erschriften 3/F-J/ G/Gelen kwelle an die Masc hine montieren @ 514\mod_150 4174553825_ 78.docx @ 3 535098 @ 3 @ 1
7.5.2 Mounting the universal shaft at the machine
Pos: 40.39.2 /B A/Sicherheit/Gel enkwelle/Gefa hr - Sich dreh ende Gelenkwelle _2 @ 0\ mod_119978169295 0_78.docx @ 3 4523 @ @ 1
Danger! - Rotating PTO shaft
Effect: Danger to life or serious injuries
• Install or detach the PTO shaft only with the engine switched off and the ignition key
removed.
• Secure the tractor against rolling.
• Make sure that the PTO shaft is coupled properly (the lock of the PTO shaft must have
snapped in).
• Make sure that the protective devices are attached properly.
• Never use a PTO shaft, the protective devices of which have not been attached.
• Replace damaged protective devices immediately
• Attach the safety chain of the PTO shaft so that the guard tube does not rotate
simultaneously with the PTO shaft.
Pos: 40.39.3 /B A/Sicherheit/Gel enkwelle/Gefa hr - Antriebsdre hzahl 540 beac hten @ 3\mod _12053165182 45_78.docx @ 73595 @ @ 1
Danger! - Observe drive speed
Effect: Danger to life or serious injuries
• This machine is driven at a maximum PTO speed of 540 rpm.
Pos: 40.39.4 /B A/Inbetriebnahm e/Wender/Anba u Gelenkwelle/Hin weis Montag e Gelenkwelle @ 20\mod_ 1239024536740 _78.docx @ 227900 @ @ 1
Note
When mounting the universal shaft, make sure that the overload protection system will be
installed on the side of the machine.
Pos: 40.39.5 /Üb erschriften/Zwisch enüberschrift en/U-Z/Vor aussetzung @ 463\mod_14665 72209300_78.d ocx @ 312372 6 @ @ 1
Prerequisite
Pos: 40.39.6 /B A/Erstinbetriebna hme/Rundballe npresse/Gel enkwelle/Gelen kwelle von Pic k-up demonti ert und Schutzt opf montiert_Vora ussetzung @ 5 14\mod_150418 2327646_78.d ocx @ 3535 859 @ @ 1
– You have dismounted the universal shaft from the pick-up and unpacked it.
– You have mounted the protective cap, see chapter Commissioning, "Mounting the
protective cap for the universal shaft of the tractor".
Pos: 40.39.7 /B A/Erstinbetrie bnahme/Rundb allenpresse/Gel enkwelle/Gelen kwelle an die Masc hine montier en_Bild1_Co mprima_Fortim a @ 514\mod _1504182018229 _78.docx @ 3535765 @ @ 1
Fig.
Pos: 40.39.8 /B A/Erstinbetriebna hme/Rundballe npresse/Gel enkwelle/Gelen kwelle an der Masc hine montieren _Text1_Com prima_Fortima @ 514\mod_ 15041828027 36_78.docx @ 3535890 @ @ 1
• Remove the screw connection (2) from the universal shaft (1).
Pos: 40.39.9 /L ayout Module /---------------Seitenumbruch---------------- @ 0\mod_11961 75311226_0.d ocx @ 4165 @ @ 1
To Next Page
Loading...
