Krone Comprima F 155 XC - 14.2 Lubricants; 14.3 Lubricating Universal Shaft

Maintenance – lubrication
255
Pos: 54.6 /Übersc hriften/Übersc hriften 2/P-T/ S/Schmierstoffe @ 17\mod_12 36177314933 _78.docx @ 20 1837 @ 2 @ 1
14.2 Lubricants
Pos: 54.7 /BA/W artung/Großpac kenpressen/Sch mierung / Sc hmierplan/Allg emeines_unterschie dliche Sch miersysteme @ 432 \mod_1 456208444064_ 78.docx @ 2981 922 @ @ 1
Depending on the version, the machine is equipped with different lubrication systems.
Soft, supple NLGI Class 2 lithium soap greases in accordance with DIN 51825 with EP additives
should be used as lubricating greases. KRONE recommends not using lubricating greases with
any other base material.
Pos: 54.8 /BA/W artung/Großpac kenpresse n/Schmierung / Sc hmierplan/Für ei ne Auflistung d er Schmierstoff e siehe Kapitel _Verweis @ 4 16\mod_1453 207195835_7 8.docx @ 29191 14 @ @ 1
The listing of lubricants can be found in chapter Technical Data, “Consumables”.
Pos: 54.9 /BA/W artung/Großpac kenpresse n/Schmierung / Sc hmierplan/Absch mieren Te xt allgemein @ 24 \mod_1241683 749117_78.doc x @ 247535 @ @ 1
Lubrication points on the machine must be lubricated at regular intervals. The position of the
lubrication points and the lubrication intervals can be seen in the lubrication plans in the
operating instructions. Remove the grease that comes out of the bearing points after lubrication.
Pos: 54.10 /Übersc hriften/Überschrif ten 2/F-J /G/Gelenkwell e schmieren @ 4 16\mod_14 53299872686_78. docx @ 29211 78 @ 2 @ 1
14.3 Lubricating Universal Shaft
Pos: 54.11 /BA/ Wartung/Rundballe npresse/Sc hmierung/Schmi erplan/Bild Gelen kwelle Compr. außer X-tr @ 361\mod_ 1439456809154 _78.docx @ 266 8211 @ @ 1
1 2 1
1
44
3
Fig.
222
Pos: 54.12 /BA/ Wartung/Gelen kwelle schmiere n/Abschmieren Gelenkwelle in Gr amm_BiG Pac k, Fortima, Co mprima (außer X- tr) @ 353\ mod_143772 7202539_78.doc x @ 2641521 @ @ 1
Lubricate the universal shafts at the marked lubrication points by means of multi-purpose
grease. The following table provides information on lubrication interval and gram number per
lubrication point. Observe operating instructions of universal shaft manufacturer.
Pos: 54.13 /BA/ Wartung/Rundballe npresse/Sc hmierung/Schmi erplan/Tabelle Sc hmierstellen Gel enkwelle_Co mprima außer X-tr @ 36 1\mod_14394 76525404_78.doc x @ 2668304 @ @ 1
Pos.
Lubricant quantity
Lubrication interval
1
18 g
50 h
2
60 g
50 h
3
20 g
50 h
4
6 g
50 h
Pos: 54.14 /La yout Module /---------------Seitenumbruch---------------- @ 0\mod_11961 75311226_0.doc x @ 4165 @ @ 1