Central Office Calls, Answering
Aspila EX Software Manual Features 117
14-01-03 : Basic Trunk Data Setup - Receive CODEC Gain Type
Customize the transmit and receive levels of the CODEC Gain Types for each trunk.
• 14-02-02 : Analogue Trunk Data Setup - Ring Detect Type
For each trunk, enable delayed ringing (0) or immediate ringing (1).
• 14-05-01 : Trunk Groups
For Universal Answer, assign trunks to trunk groups (1-100) then go to Program 14-06 below
to set up Trunk Group Routing.
• 14-06-01 : Trunk Group Routing
For Universal Answer, set up trunk routes (1-100) and then go to Program 23-03 below to
assign the trunk routes to extensions. An extension user can use Universal Answer to answer a
call if the ringing trunk is in its assigned route.
• 14-07-01 : Trunk Access Map Setup
Set up the Trunk Access Maps (1-200). This sets the access options for trunks. Ring Group
programming overrides Access Map programming.
• 15-02-02 : Multi-Line Telephone Basic Data Setup - Trunk Ring Tone
Trunks ring extensions according to the Ring Tone Range selected in 22-03 and the settings
made with either Service Code 820 or Program 15-02-02. Also see Program 22-03.
• 15-06-01 : Trunk Access Map for Extensions
Assign Trunk Access Maps (1-200) to extensions.
• 15-07-01 : Programming Function Keys
To have outside calls ring specific keys, assign trunks to line keys (codes 1-200). You can
also program function keys as trunk group or loop keys (*02 or *05). For additional loop key
data, in Program 15-13 enter 0 (incoming only), 1 (outgoing only) or 2 (both ways).
• 20-02-09 : System Options for Multi-Line Telephones - Disconnect Supervision
Enable (1) disconnect supervision for the system.
• 20-06-01 : Class of Service for Extensions
For Universal Answer, assign a Class of Service (1-15) that enables Program to an extension.
• 20-10-07 : Class of Service Options (Answer Service) - Automatic Answer of Universal Calls
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use
Auto-Answer to pick up Universal Answer calls. This allows a user to simply pick up the
handset instead of dialing a service code.
• 20-13-23 : Class of Service Options (Supplementary Service) - Display the Reason for
Transfer
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to display
the Reason for Transfer message.
• 22-01-02 : System Options for Incoming Calls - Incoming Call Ring No Answer Alarm
Enable (1) or disable (0) the Incoming Call RNA Alarm. If enabled, the ring cadence will
change for a call that rings longer than the interval set in 22-01-03.
• 22-01-03 : System Options for Incoming Calls - Ring No Answer Alarm Time
Set the Ring No Answer Alarm interval (0-64800 seconds). If a trunk rings a system phone-
system phone longer than this interval, the system changes the ring cadence.
• 22-01-04 : System Options for Incoming Calls - DIL No Answer Time
If an incoming trunk call rings longer than this interval, it reroutes to the Ring Group set in
Program 22-08.
• 22-03-01 : Trunk Ring Tone Range
Assign Ring Tone Ranges to trunks. Customize the tones within each Ring Tone Range in 82-
01. Trunks ring extensions according to the Ring Tone Range selected in 22-03 and the set-
tings made with either Service Code 820 or Program 15-02-02.
• 22-04-01 : Incoming Extension Ring Group Assignment
To have trunks ring extensions, assign extensions to ring groups (1-100). For each extension
in the Ring Group, indicate in Program 22-06 if trunks should ring (1) or not ring (0).
To Next Page
Loading...
