NEC ASPILA EX - Page 94

Automatic Route Selection (F-Route)
80 Features Aspila EX Software Manual
• 44-03-03 : Dial Analysis Extension Table - Table Number (251)
Select the ARS/R-Route table number (0-500) to be used for the Dial Extension Analyze
Table 251.
• 44-03-04 : Dial Analysis Extension Table - Next Table Number
Select the Next Table Area Number (0-4) to be used for the Dial Extension Analyze Table
252.
• 44-04-01 : ARS/F-Route Selection for Time Schedule
Assign each ARS/F-Route Selection number (1-500) to an ARS/F-Route table number for
each ARS/F-Route time mode. There are 8 time modes for ARS/F-Route Access.
• 44-05-02 : ARS/F-Route Table - Delete Digits
For each ARS/F-Route table (1-500) assign a priority number (1-4). Enter the number of dig-
its to be deleted (0-255).
• 44-05-03 : ARS/F-Route Table - Additional Dial Number
For each ARS/F-Route table (1-500) assign a priority number (1-4). Enter the number of addi-
tional digits to be dialed (0-1000).
• 44-05-04 : ARS/F-Route Table - Beep Tone
For each ARS/F-Route table (1-500) assign a priority number (1-4). Select whether or not a
beep is heard if a lower priority trunk group is used (0=no beep, 1=beep).
• 44-05-05 : ARS/F-Route Table - Gain Table Number for Internal Call
For each ARS/F-Route table (1-500) assign a priority number (1-4). Select the gain table
number to be used for internal calls (0-500).
• 44-05-06 : ARS/F-Route Table - Gain Table Number for Tandem Connections
For each ARS/F-Route table (1-500) assign a priority number (1-4). Select the gain table
number to be used for tandem connection (0-500).
• 44-05-07 : ARS/F-Route Table - ARS Class of Service
For each ARS/F-Route table (1-500) assign a priority number (1-4). Select the Class of Ser-
vice to be used for ARS (0-16).
• 44-05-08 : ARS/F-Route Table - Dial Treatment
For each ARS/F-Route table (1-500) assign a priority number (1-4). Select the Dial Treatment
to be used (0-15).
• 44-06-01 : Additional Dial Table
Set the additional dial table (1-1000) to add prior to the dialed ARS/F-Route number.
• 44-07-01 : Gain Table for ARS/F-Route Access - Incoming Transmit
44-07-02 : Gain Table for ARS/F-Route Access - Incoming Receive
44-07-03 : Gain Table for ARS/F-Route Access - Outgoing Transmit
44-07-04 : Gain Table for ARS/F-Route Access - Outgoing Receive
Set the gain table to be used (1-500). If an extension dials ARS/F-Route number;
- The Extension Dial Gain Table is activated, which is assigned in Program 44-05.
- The Extension Dial Gain Table follows “Outgoing transmit” and “Outgoing receive” settings.
If the incoming call is transferred to another line using ARS/F-Route;
- The Tandem Gain Table is activated, which is assigned in Program 44-05.
- The Tandem Gain Table follows the “Incoming transmit” and “Incoming receive” settings
for incoming line, and “Outgoing transmit” and “Outgoing receive” settings for the outgoing
line.
For the ARS/F-Route call (in the above case), CODEC gain in Program 14-01-02 and 14-01-
03 are not activated.
• 44-08-01 : Time Schedule for ARS/F-Route
Define the daily pattern of the ARS/F-Route feature. ARS/F-Route has 10 time patterns.
These patterns are used in Program 44-09 and 44-10. The daily pattern consists of 20 time set-
tings.