YASKAWA V1000 Series Installation & Start-Up Manual

B.2 Parameter Table
354 YASKAWA TM.V1000.01 V1000 Drive Installation & Start-Up Manual (Preliminary 01-19-07)
d4-06
Frequency
Reference Bias
(Up/Down 2)
100% = Max output frequency (E1-04).
Saves the bias value once the frequency
reference is adjusted.
The bias can be set by the user, but will be
disabled under the following conditions:
When none of the multi-function input terminals
are assigned +0 frequency reference bias
function.
When the frequency reference priority has
changed (including multi-step speed).
When both d4-03 = 0 and d4-05 = 1 while the
Up 2 / Down 2 commands are both on or both
off.
When the max output frequency has changed
(E1-04).
When the digital frequency reference has
changed.
-99.9 to
+100.0
0.0
%
AAA 2AD —
d4-07
<22>
Analog Frequency
Reference
Fluctuation Limit
(Up/Down 2)
• When the Up 2 and Down 2 commands are
enabled, the frequency reference holds the bias
value as the levels for the analog frequency
reference or pulse train frequency reference
change, accelerating or decelerating to the
frequency reference.
• After frequency agree is achieved, the bias
process starts again.
• Enabled only when the analog or pulse train
reference is on.
0.1
to
+100.0
1.0
%
AAA 2AE —
d4-08
<22>
Frequency
Reference Bias
Upper Limit (Up/
Down 2)
When d4-06 is greater than d4-08, d4-08
becomes the bias for the upper limit.
Set as a percentage of the max output frequency.
0.1
to
100.0
0.0
%
AAA 2AF —
d4-09
<22>
Frequency
Reference Bias
Lower Limit (Up/
Down 2)
When d4-06 is less than d4-09, d4-09 becomes
the bias for the lower limit.
Set as a percentage of the max output frequency.
-99.9
to 0.0
0.0
%
AAA 2B0 —
d7: Offset Frequency
Use d7 parameters to set the offset frequency.
d7-01
<22>
Offset Frequency 1
Added to the frequency reference when one of
the multi-function input terminals is set
(H1- = 44) and switched on.
-100.0
to
+100.0
0.0
%
AAA 2B2 —
d7-02
<22>
Offset Frequency 2
Added to the frequency reference when one of
the multi-function input terminals is set
(H1- = 45) and switched on.
-100.0
to
+100.0
0.0
%
AAA 2B3 —
No. Name Description Range Def.
Control
Mode
Addr.
Hex
Pg.
V/
f
O
L
V
P
M

YASKAWA V1000 Series Specifications

General

Model	V1000 Series
Series	V1000
Output Frequency	0.1 to 400 Hz
Overload Capacity	150% for 60 seconds
Type	AC Drive
Control Method	V/f Control
Input Voltage	200-240V, 380-480V
Output Voltage	0 to Input Voltage
Power Range	0.1 to 18.5 kW
Horsepower	0.2 to 25 HP
Protection Features	Overcurrent, Overvoltage, Undervoltage, Overheating, Short Circuit, Ground Fault
Communication Interfaces	Modbus RTU
Enclosure	IP20
Ambient Temperature	-10 to +50°C
Storage Temperature	-20 to +60°C
Humidity	5 to 95% RH (non-condensing)
Cooling Method	Fan Cooled