Cisco ASR 9000 Series Command Reference

Task ID
OperationTask ID
readnetwork
readconfig-services
Examples
These are some of the options for the show subscriber session command in the EXEC mode:
RP/0/RSP0/CPU0:router# show subscriber session all
RP/0/RSP0/CPU0:router# show subscriber session all summary location 0/1/CPU0
RP/0/RSP0/CPU0:router# show subscriber session filter vrf vrf1 location 0/1/CPU0
RP/0/RSP0/CPU0:router# show subscriber session subscriber-label 40
This is the sample output of the show subscriber session all command:
Wed Jan 23 10:20:58.344 GMT
Codes: IN - Initialize, CN - Connecting, CD - Connected, AC - Activated,
ID - Idle, DN - Disconnecting, ED - End
Type Interface State Subscriber IP Addr / Prefix
LNS Address (Vrf)
--------------------------------------------------------------------------------
PPPoE:PTA Gi0/1/0/0.pppoe1 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe2 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe3 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe1 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe2 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe3 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe1 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe2 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe3 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe1 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe2 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe3 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe4 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe5 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe6 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe4 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe5 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe6 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe4 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe5 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe6 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe4 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe5 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe6 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe7 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe8 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe9 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe7 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe8 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.1.pppoe9 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe7 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe8 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.2.pppoe9 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe7 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe8 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.3.pppoe9 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe10 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe11 AC 100.0.0.1 (default)
PPPoE:PTA Gi0/1/0/0.pppoe12 AC 100.0.0.1 (default)
Cisco ASR 9000 Series Aggregation Services Router Broadband Network Gateway Command Reference, Release
5.2.x
567
Subscriber Commands
show subscriber session

Cisco ASR 9000 Series Specifications

General

Series	ASR 9000
Category	Network Router
Modular Design	Yes
Redundancy	Yes (Hardware and Software)
Operating System	Cisco IOS XR
Interfaces/Ports	10G, 40G, 100G, 400G Ethernet
Expansion Slots	Varies by model
Routing Protocol	BGP, OSPF, IS-IS, EIGRP
Management	CLI, SNMP, NETCONF
Power Supply	Redundant
Port Density	Varies by model
Power Supply Options	AC, DC
Memory	Varies by model
Storage	Varies by model
Dimensions	Varies by model
Weight	Varies by model