D-Link xStack - Page 122

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
117
<value 0-65535> - Enter the value between 0 and 65535.
protocol_id - Specifies that the rule will apply to the value of IP protocol ID traffic.
<value 0-255> - Enter the value between 0 and 255.
user_define - (Optional) Specify that the rule will apply to the IP protocol ID and that the mask
options behind the IP header, which has a length of 4 bytes.
<hex 0x0-0xffffffff> - Enter that the rule will apply to the IP protocol ID and that the mask
options behind the IP header , which has a length of 4 bytes.
packet_content - Specifies that the access control list rule will be set to packet content.
offset_0-15 - Specifies the mask for packet bytes 0-15.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 0-3.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 4-7.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 8-11.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 12-15.
offset_16-31 - Specifies the mask for packet bytes 16-31.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 16-19.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 20-23.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 24-27.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 28-31.
offset_32-47 - Specifies the mask for packet bytes 32-47
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 32-35.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 36-39.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 40-43.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 44-47.
offset_48-63 - Specifies the mask for packet bytes 48-63.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 48-51.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 52-55.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 56-59.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 60-63.
offset_64-79 - Specifies the mask for packet bytes 64-79.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 64-67.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 68-71.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 72-75.
<hex 0x0-0xffffffff> - Enter the mask for packet bytes 76-79.
ipv6 - Specifies that the rule applies to IPv6 fields.
class - Specifies the value of the IPv6 class.
<value 0-255> - Enter the value between 0 and 255.
flowlabel - Specifies the value of the IPv6 flow label.
<hex 0x0-0xfffff> - Enter the value of the IPv6 flow label.
source_ipv6 - Specifies the value of the IPv6 source address.
<ipv6addr> - Enter the value of the IPv6 source address.
destination_ipv6 - Specifies the value of the IPv6 destination address.
<ipv6addr> - Enter the value of the IPv6 destination address.
port - Specifies the port number to configure.
<portlist> - Enter a list of ports.
all - Specifies to configure all ports.
permit - Specifies the packets that match the access profile are permitted by the switch.
deny - Specifies the packets that match the access profile are filtered by the switch.
time_range - (Optional) Specify the name of this time range entry.
<range_name 32> - Enter the name of this time range entry. The maximum length is 32
characters.
delete access_id - Specifies to delete the access ID.
<value 1-100> - Enter the value between 1 and 100.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command.