D-Link xStack - Page 911

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
906
routers. A value of zero represents an ‘infinite’ interval, and indicates that periodic PIM6 Hello
message should not be sent on this interface.
<sec 0-18000> - Enter the hello packet interval value here. This value must be between 0 and
18000 seconds. The default value is 30 seconds.
triggered_hello_delay - (Optional) Specifies the maximum time before the router sends a
triggered PIM Hello message on the specified interface. A value of zero has no special
meaning and indicates that triggered PIM6 Hello message should always be sent immediately.
<sec 0-60> - Enter the triggered hello delay value here. This value must be between 0 and 60
seconds. The default value is 5 seconds.
propagation_delay - (Optional) Specifies the expected propagation delay between the PIM6
routers on this network or link.
<sec 0-32> - Enter the propagation delay value here. This value must be between 0 and 32
seconds. The default value is 1 second.
override_interval - (Optional) Specifies the value this router inserts into the Override_Interval
field of the LAN Prune Delay option in the PIM6 Hello messages. When overriding a prune,
PIM6 routers pick random time duration up to the value of this object.
<sec 0-65> - Enter the override interval value used here. This value must be between 0 and
65 seconds. The default value is 3 seconds.
jp_interval - (Optional) Specifies the frequency at which this router sends PIM6 Join/Prune
messages on this PIM6 interface. A value of zero represents an ‘infinite’ interval, and indicates
that periodic PIM6 Join/Prune messages should not be sent on this interface.
<sec 0-18000> - Enter the Join/Prune interval value used here. This value must be between 0
and 18000 seconds. The default value is 60 seconds.
dr_priority - (Optional) Specifies the Designated Router Priority value inserted into the DR
Priority option in PIM6 Hello message transmitted on this interface. Numerically higher values
for this parameter indicate higher priorities.
<uint 0-4294967294> - Enter the Designated Router priority value used here. This value must
be between 0 and 4294967294. The default value is 1.
bsr_border - (Optional) Specifies whether or not this interface is a PIM6 domain border. If this
interface configures a border, which will prevent bootstrap router (BSR) messages from being
sent or received through it. By default, an interface is not PIM6 domain border.
disable - Specifies that this interface is not a PIM6 domain border.
enable - Specifies that this interface is a PIM6 domain border.
stub_interface - (Optional) Specifies whether this interface is a stub interface. If this interface
configures a stub interface, then no PIM6 packets are sent out this interface, and any received
PIM6 packets are ignored. By default, an interface is not stub interface. When enabled, it is a
security measure for interfaces towards untrusted hosts. It protects the PIM router from forged
PIM messages on the interface.
disable - Specifies that this interface is not a stub interface.
enable - Specifies that this interface is a stub interface.
state - (Optional) Allows the PIM6 to be disabled or enabled for the above IPv6 interface. By
default, the PIM6 protocol state is disabled on an interface.
enable - Specifies that PIM6 is enabled.
disable - Specifies that PIM6 is disabled.
Restrictions
Only Administrator, Operator and Power-User level users can issue this command. (EI Mode Only
Command)
Example
To set the jp_interval to 60 seconds, the hello_interval to 60 seconds and enable the PIM6 state
for interface “n10”:
DGS-3620-28SC:admin# config pim6 ipif n10 jp_interval 60 hello_interval 60
state enable
Command: config pim6 ipif n10 jp_interval 60 hello_interval 60 state enable