Hioki IM3536 - Page 142

276 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

136

Testing the System (Self diagnosis)

Table of Contents

Default Chapter3
- Table of Contents3
Introduction7
Verifying Package Contents7
Measurement Process12
Safety Information16
Operating Precautions18
1 Overview23
- Product Overview and Features23
- Names and Functions of Parts24
- Screen Layout and Operation26
2 Measurement Preparations37
- Preparation Flowchart37
- Pre-Operation Inspection39
- Connecting the Power Cord40
- Connecting the Measurement Cables, Probes, or Fixture41
- Turning the Power on and off42
- Setting the Date and Time44
3 Performing Measurements in LCR Mode45
- Setting Display Parameters45
  - X84; to Perform DC Measurement (DC Resistance Measurement)46
- Viewing Measured Values47
- Enlarging Display of Measurement Values48
- Setting Measurement Conditions (Basic Settings)49
- Judging Measurement Results74
- Setting Application Settings85
4 Using Continuous Measurement Mode99
- Setting Which Panels to Use in Continuous Measurement99
- Performing Continuous Measurement100
- Checking Continuous Measurement Results100
- Changing the Display Timing Setting (When You Wish to Shorten the Screen Update Interval)101
- Setting the LCD Display Auto-Off (When You Wish to Save the Power)102
5 Error Correction103
- Setting the Cable Length (Cable Length Correction)104
- Open Correction105
- Short Correction111
- If Open or Short Correction Fails to Complete Normally115
- Disabling Open and Short Correction Values117
- Load Correction (Correcting Values to Match Reference Values)118
- Correcting Measured Values with a User-Specified Correction Coefficient (Correlation Correction)127
6 Saving and Loading Measurement Condition and Correction Value Data129
- Saving Measurement Conditions and Correction Values (Panel Save Function)130
- Loading Measurement Conditions and Correction Values (Panel Load Function)134
- Changing a Panel Name135
- Deleting a Panel136
7 Setting the System137
- Setting the Interface (Controlling the Instrument from a Computer)138
- Checking the Version of the Instrument138
- Testing the System (Self Diagnosis)139
8 Using USB Flash Drive (Saving and Loading Data)143
- Inserting and Removing a USB Flash Drive144
- Checking the Contents of Files on a USB Flash Drive145
- Formatting a USB Flash Drive146
- Saving Measurement Data147
- Saving Settings Data159
  - X84; Saving Instrument Settings Other than Panels159
  - Panels (ALL SAVE Function)160
- Loading Instrument Settings161
  - X84; Loading Settings Files or Panel Files161
  - Files (ALL LOAD Function)162
- Checking the Contents of a File163
- Deleting Files and Folders164
- Creating Folders165
- Displaying the USB Flash Drive Information166
9 External Control167
- External Input/Output Connector and Signals168
- Example Measurement Timing (Timing Charts)177
- Internal Circuitry182
- External I/O Settings186
- External Control Q&A191
- Result Output to EOM Output) and Judgment Result Reset Operation191
- Measurement Using a Computer192
10 Specifications193
- General Specifications193
- Environmental and Safety Specifications198
- Accessories and Options199
- Function Specifications199
- Interfaces211
- Measurement Range and Accuracy213
- About Measurement Times and Measurement Speed223
11 Maintenance and Service227
- Calibration, Inspection, Repair, and Cleaning227
- Troubleshooting229
- Error Massage and Error Display236
- Discarding the Instrument241
  - Formula243
Appendix Appx243
- Appx. 3 Measurement of In-Cir Cuit Components246
- External Noise247
- X84; Countermeasures against Incorporation of Noise from the Power Line247
- X84; Countermeasures against Noise from the Measurement Cables248
Appx. 5 Supplying DC Bias248
- X84; How to Supply a DC Bias Voltage249
- X84; How to Supply a DC Bias Current250
- Appx. 6 the Residual Charge Protection Function251
Appx. 7 Series Equivalent Circuit Mode and Parallel Equivalent252
- Short Correction253
  - Appx. 8 Open Correction and Short Correction253
  - Hardware to the Instrument Appx254
- Appx.12255
Appx. 10 Dimensional Diagram256
Appx. 11 Initial Settings Table257
- Appx. 12 Device Compliance Statement264

Related product manuals

Preview: Hioki IM3533

Preview: Hioki IM3533-01

Hioki IM3533-01

Preview: Hioki IM3523

Preview: Hioki IM3570

Hioki IM7580A Series

Preview: Hioki PW3198

Preview: Hioki PQ3198

Preview: Hioki CM4375

Preview: Hioki 3169-20

Preview: Hioki 3280-10F

Preview: Hioki BT3562-01

Hioki BT3562-01