Honeywell DR4500A User Manual

Release M DR4500A Classic Series Circular Chart Recorder With or Without Control Product Manual xi
April 2017
Table 4-14 Lockout group definitions ..................................................................................................................... 114
Table 5-1 Install/replace chart ................................................................................................................................. 116
Table 5-2 Set the chart time line procedure ............................................................................................................. 118
Table 5-3 Power up diagnostic tests ........................................................................................................................ 118
Table 5-4 Procedure for testing the displays and keys............................................................................................. 119
Table 5-5 Procedure for starting up the recorder ..................................................................................................... 120
Table 5-6 Meaning of indicators .............................................................................................................................. 123
Table 5-7 Lower display key parameter prompts .................................................................................................... 125
Table 5-8 Error messages ........................................................................................................................................ 126
Table 5-9 Alarm and tuning messages ...................................................................................................................... 127
Table 5-10 Operating mode definitions ................................................................................................................... 129
Table 5-11 Changing operating modes .................................................................................................................... 129
Table 5-12 Procedure for selecting automatic or manual mode .............................................................................. 130
Table 5-13 Procedure for selecting the setpoint source ........................................................................................... 131
Table 5-14 Procedure for changing the local setpoint ............................................................................................. 131
Table 5-15 Procedure for switching between setpoints ........................................................................................... 132
Table 5-16 Setpoint selection indication ................................................................................................................. 132
Table 5-17 Procedure for configuring a single setpoint ramp.................................................................................. 133
Table 5-18 Procedure for running a setpoint ramp .................................................................................................. 134
Table 5-19 Procedure for selecting two sets of tuning constants ............................................................................. 136
Table 5-20 Procedure for setting switchover values ................................................................................................ 137
Table 5-21 Procedure for setting tuning constant values ......................................................................................... 137
Table 5-22 Procedure for switching PID sets from the keyboard ............................................................................ 138
Table 5-23 Procedure for starting Accutune II ......................................................................................................... 139
Table 5-24 Procedure for using Accutune for duplex control.................................................................................. 140
Table 5-25 Procedure for displaying or changing the alarm setpoints ...................................................................... 142
Table 5-26 Digital input option action on contact closure ....................................................................................... 143
Table 5-27 Procedure for resetting the totalizer ...................................................................................................... 144
Table 5-28 Procedure for displaying the totalizer value .......................................................................................... 145
Table 5-29 Maximizing pen life .............................................................................................................................. 146
Table 5-30 Changing the ink cartridge .................................................................................................................... 147
Table 5-31 Replacing a chart lamp .......................................................................................................................... 147
Table 6-1 Parameter settings for example 12-step profile ........................................................................................ 155
Table 6-2 Setpoint program data entry procedure ................................................................................................... 159
Table 6-3 SP RAMP prompts and available selections ............................................................................................ 161
Table 6-4 Setpoint program profiles group definitions ............................................................................................ 163
Table 6-5 Setpoint program segments group definitions ......................................................................................... 165
Table 6-6 Setpoint program event group definitions ............................................................................................... 168
Table 6-7 Segment event relay operation requirements ............................................................................................ 169
Table 6-8 Run/Monitor functions ............................................................................................................................ 172
Table 7-1 Restoring factory calibration ................................................................................................................... 176
Table 7-2 Voltage and resistance equivalents for 0% and 100% range values ........................................................ 178
Table 7-3 Disconnect the field wiring ..................................................................................................................... 180
Table 7-4 Equipment needed ................................................................................................................................... 181
Table 7-5 General set up procedure ......................................................................................................................... 183
Table 7-6 Set up wiring procedure for Thermocouple inputs using an ice bath ...................................................... 184
Table 7-7 Set up wiring procedure for Thermocouple inputs using a compensated calibrator method ................... 185
Table 7-8 Set up wiring procedure for Thermocouple inputs using the ambient temperature method .................... 186
Table 7-9 Set up wiring procedure for RTD inputs ................................................................................................. 187
Table 7-10 Set up wiring procedure for Radiamatic, Millivolts, and Volts inputs (except 0-10 Volts) .................. 188
Table 7-11 Set up wiring procedure for 0–10 Volt inputs ....................................................................................... 189
Table 7-12 Set up wiring procedure for 4–20 mA inputs ........................................................................................ 190
Table 7-13 Calibration procedure sequence ............................................................................................................ 191
Table 8-1 Set up wiring procedure current proportional output/Aux Out 2 and 3 ................................................... 195
Table 8-2 Current proportional output/Aux Out 2 and 3 calibration procedure ...................................................... 196

Honeywell DR4500A Specifications

General

Brand	Honeywell
Model	DR4500A
Category	Recording Equipment
Language	English