Keysight Technologies InfiniiVision DSOX1204A User Manual

944 Keysight InfiniiVision DSOX1204A/G Oscilloscopes Programmer's Guide
Index
start print job, 324
start time, 609, 737
start time marker, 734
state memory, 124
state of instrument, 117, 567
status, 127, 162, 164
Status Byte Register (STB), 125, 127, 128,
770
status data structure clear, 111
status registers, 48
status reporting, 765
STB (Status Byte Register), 125, 127, 128,
770
step size for frequency span, 268, 295
stop, 143, 163
stop acquisition, 163
stop cursor, 738
stop displaying channel, 142
stop displaying math function, 142
stop displaying pod, 142
stop on mask test failure, 422
stop time, 609, 738
storage, 124
store instrument setup, 117, 124
store setup, 124
storing calibration information, 194
string variables, 46
string variables, reading multiple query
results into, 47
string variables, reading query results into
multiple, 47
string, quoted ASCII, 104
subnet mask, 34
subsource, waveform source, 658
subsystem commands, 3, 803
subtract math function, 291, 303, 654
subtract math function as g(t) source,
299
sweep mode, trigger, 585, 596
sweep speed set to fast to measure fall
time, 362
sweep speed set to fast to measure rise
time, 377
switch disable, 552
sync break, LIN, 500
syntax elements, 103
syntax rules, program data, 802
syntax, optional terms, 103
syntax, program message, 799
SYSTem commands, 545
system commands, 548, 550, 551, 552,
567, 569
system commands introduction, 547
T
tdelta, 733
tedge, 382
telnet ports 5024 and 5025, 642
temporary message, 550
TER (Trigger Event Register), 164, 773
termination conditions, mask test, 418
test sigma, mask test run, 423
test, self, 130
text, writing to display, 550
threshold voltage (lower) for
measurement, 731
threshold voltage (upper) for
measurement, 740
thresholds, 357, 734
thresholds used to measure period, 371
thresholds, how autoscale affects, 137
time base, 575, 576, 577, 578, 579, 755
time base commands introduction, 574
time base reset conditions, 122, 557
time base window, 581, 582, 583
time between points, 733
time buckets, 179, 180
time delay, 755
time delta, 733
time difference between data points, 662
time duration, 609
time holdoff for trigger, 590
time interval, 382, 384, 733
time interval between trigger and
occurrence, 739
time marker sets start time, 734
time measurements with X cursors, 334
time per division, 577
time record, 270, 297
time specified, 393
time, calibration, 200
time, mask test run, 424
time, start marker,
737
time, stop marker, 738
time, system, 569
time, transition trigger, 626
time/div, how autoscale affects, 137
time-at-max measurement, 735
time-at-min measurement, 736
TIMebase commands, 573
timebase vernier, 580
TIMebase:MODE, 44
time-ordered label list, 237
timeout, SPI clock, 511
timing measurement, 350
title channels, 210
title, mask test, 432
tolerance, automask, 408, 409
top of waveform value measured, 394
total frame count (CAN), 471
total waveforms in mask test, 413
trace memory, 162
track measurements, 379
transfer instrument state, 117, 567
transition trigger qualifier, 623
transition trigger slope, 624
transition trigger source, 625
transition trigger time, 626
transparent screen background, remote
command logging, 565
tree traversal rules, 803
TRG (Trigger), 126, 128, 129
trigger armed event register, 150, 152
trigger burst, UART, 538
trigger channel source, 610, 631
TRIGger commands, 585
TRIGger commands, general, 587
trigger data, UART, 539
TRIGger EDGE commands, 597
trigger edge coupling, 598
trigger edge slope, 601
trigger event bit, 164
Trigger Event Register (TER), 773
TRIGger GLITch commands, 603
trigger holdoff, 590
trigger idle, UART, 540
TRIGger IIC commands, 483
trigger level auto set up, 591
trigger level constants, 212
trigger level voltage, 599
trigger level, high, 592
trigger level, low, 593
TRIGger LIN commands, 493
trigger occurred, 128
TRIGger PATTern commands, 611
trigger pattern qualifier, 615
trigger qualifier, UART, 541
trigger reset conditions, 122, 557
TRIGger SHOLd commands, 616
trigger SPI clock slope, 510
TRIGger SPI commands, 507
trigger status bit, 164
trigger sweep mode, 585
TRIGger TV commands, 622, 627
trigger type, SPI, 521
trigger type, UART, 542
TRIGger UART commands, 523
trigger, CAN, 477
trigger, CAN pattern data length, 480
trigger, CAN pattern ID mode, 482
trigger, CAN sample point, 473
trigger, CAN signal baudrate, 474
trigger, CAN signal definition, 475
trigger, CAN source, 476
trigger, edge coupling, 598
trigger, edge level, 599
trigger, edge reject, 600
trigger, edge slope, 601
trigger, edge source, 602
trigger, force a, 588
trigger, glitch greater than, 604
trigger, glitch less than, 605
trigger, glitch level, 606
trigger, glitch polarity, 607
trigger, glitch qualifier, 608
trigger, glitch range, 609
trigger, glitch source, 610
trigger, high frequency reject filter, 589
trigger, holdoff, 590
trigger, IIC clock source, 485
trigger, IIC data source, 486
trigger, IIC pattern address, 487
trigger, IIC pattern data, 488
trigger, IIC pattern data 2, 489
trigger, IIC qualifier,
490

Keysight Technologies InfiniiVision DSOX1204A Specifications

General

Brand	Keysight Technologies
Model	InfiniiVision DSOX1204A
Category	Test Equipment
Language	English